8. Ensure to insert battery before you install the alarm, or you
will destroy the unit.
9. Close the cover with the alarm according to Diagram 4,and
then finish your installation.
DIAGRAM 4
PUSH
1.
Never use water, cleaners or solvents to clean your
smoke alarm since they may damage the unit.
2. Test it at least once a week.
3. Clean the smoke alarm at least once a month. Gently vacuum
off any dust using your household vacuum’s soft brush
attachment. Open the cover and disconnect the battery, gently
vacuum the inside of the cover and the sensor chamber,
reconnect the battery. close the smoke alarm and vacuum the
outside of the cover, test the smoke alarm.
4. Use these batteries to replace the old one.
Carbon zinc:
EVEREADY 216 OR 2122;GOLDPEAK 1604P
OR 1604S
Alkaline:
EVEREADY 522 DURACELL MN1604 Ms1604;
GOLDPEAK 1604A
Lithium:
ULTRALIFE U9VL
5. When regularly checking, you should save energy as possible
as you can, because the alarm energy consumption is very
much.
Special attention:
1) Choose durable battery as possible as you can that will make
battery’s using time longer.
2) Notice whether the indicator lamp flash once 45sec normally
or not. There is two reasons that the indicator lamp don’t flash.
One is that the battery’s energy is shortage, the other is that the
battery is not fixed fitly. The simple way is to replace the battery
or refix the battery.
6. After installation you must notice whether the key indicator
flash once 45sec or not, and press the key for several seconds
to see whether the buzzer can give sound or not, if do, that
shows normal. Above is required to do, otherwise the smoke
alarm you installed probably don’t work.
1. United States NFPA72 tells that the safety of life is to be
noticed by alarms before fire, to confirm the correct escape way.
The fire systems help half of residents escape and we should
help the old people, women and children more because they are
always the victims.
2. Smoke alarms are not foolproof, they can't prevent or
extinguish fires, they are not substitute for property or life
insurance. You need buy some fire fighting facilities.
3. Sometimes the smoke is blocked by objects and can’t reach
the detector, and if the wind blows the smoke away from the
detector, the unit won’t work either.
1. Call the Fire Department immediately after confirming the fire.
2. Don’t panic, stay calmly and follow your family escape plan.
Get out of the house as quickly as possible, don’t stop to get
dressed or collect anything.
3. Feel doors before opening them to see if they are hot. If a
door is cool, open it slowly. Don’t open a hot door-use an
alternate escape route
4. Cover your nose and mouth with a cloth. (preferably wet).
Take short, shallow breath.
5. Meet at your planned place outside your home, and do a
head count to ensure everybody go out safely.
I
t is important to test this unit weekly to make sure it is
working properly. Don’t open the alarms by yourself, return
them to the seller if improperly, and don’t use fire to test
your alarms.
1. Press and hold the test button on the cover of the unit until
the alarm sounds. If it does not alarm, make sure that the unit is
receiving power and test it again. If it still does no1 alarm,
replace it immediately or check your battery.
2. The signal flashes once 30 seconds and while it alarms the
TEST
HOW TO DO IN CASE OF FIRE
LIMITATIONS OF SMOKE ALARMS
REGULAR MAINTENANCE
signal will flash once 0.5 second.
3. If the alarm makes low “chirp” sounds every about 30seconds,
it tells you to exchange your battery.
4. Little smoke will not cause alarms, so misinformation occurs
only when you blow smoke to the alarms directly or you forget to
turn on your ventilated facility while your cooking.
5. Sometimes when you smoke the unit will alarm, so you can
just blow air to it to stop alarming.
9V battery
-
+
-
+
DIAGRAM 3
9V battery
-
+
