DSE DK-WP2, Owner'S Manual, Page: 2 / 4

Document: DK-WP2-1I6 Document: DK-WP2-1I6 Document: DK-WP2-1I6
Page: 2 Page: 2
OWNER'S MANUAL
DK-WP2 camera with VCR in wall clock
DSE srl - Digital Surveillance Equipment - www.dse.eu
Once exhausted the memory capacity of the micro SD card, the device will erase the recorded
files by overwriting the oldest new recorded files.
In motion recording, DVR records video lasting 1 minute. In continuous recording it generates
files for 10 minutes.
Shooting Position
DK-WP2 recovers from a place near the front hole at 6 o'clock which provides an upright image
with the clock normally hung on the wall.
The angle is not adjustable for which it is necessary to locate the clock a suitable position to
provide a good angle of view.
IR Remote Control
DK-WP2 check with the infrared remote control that should be pointed toward the receiver placed
at 3. The button function as follows:
A - ON / OFF
B - Start recording continuous C - I shoot
D - Start recording motion E - Opens the OSD menu on the
external monitor
F - Playing back recorded movies on an external monitor G - OK button in the OSD
H / I - Buttons move in the OSD
Recording in motion detection
The recording in motion detection is the most widely used because in this DK-WP2 mode records
only in the moment in which occurs a movement in the field of view lens. Each movement creates
a recording of a minute, after which, in the absence of movements, the DVR returns to rest
conditions waiting for a new intrusion.
If you use the DK-WP2 with mains power, it starts recording in motion mode automatically when it
is connected to power.
First, to become familiar with the device,
experience this guy of
operation.
CURRENT RECORD IN MOTION
1 - Enter the DK-WP2 power adapter into the socket 1 - Enter the DK-WP2 power adapter into the socket
2 - The DVR will automatically turn on and the signal is green LED lights up for 1-2 seconds. 2 - The DVR will automatically turn on and the signal is green LED lights up for 1-2 seconds.
3 - The Motion recording starts automatically. The red LED flashes 3 times slowly. This signals 3 - The Motion recording starts automatically. The red LED flashes 3 times slowly. This signals
the start of the motion recording.
4 - To stop motion recording, press the D button on the remote. The LED returns to solid green, 4 - To stop motion recording, press the D button on the remote. The LED returns to solid green, 4 - To stop motion recording, press the D button on the remote. The LED returns to solid green,
indicating that the appliance is on standby waiting for commands
5 - Press the A button to turn off the DVR. The red LED flashes for 3 times quickly to confirm the 5 - Press the A button to turn off the DVR. The red LED flashes for 3 times quickly to confirm the
shutdown.
RECORD IN MOTION A BATTERY
1 - After turning off the DVR as seen in step 5 above, disconnect the power supply of the DK-WP2 1 - After turning off the DVR as seen in step 5 above, disconnect the power supply of the DK-WP2
from the socket.
2 - Press the A button on the remote to turn on the DVR. The Indicator LED lights green for 1-2 2 - Press the A button on the remote to turn on the DVR. The Indicator LED lights green for 1-2
seconds.
3 - The Motion recording starts automatically. The red LED flashes 3 times slowly. This signals 3 - The Motion recording starts automatically. The red LED flashes 3 times slowly. This signals
the start of the motion recording.
4 - To stop motion recording, press the D button on the remote. The LED returns to solid green, 4 - To stop motion recording, press the D button on the remote. The LED returns to solid green, 4 - To stop motion recording, press the D button on the remote. The LED returns to solid green,
indicating that the appliance is on standby waiting for commands
5 - Press the A button to turn off the DVR. The red LED flashes for 3 times quickly to confirm the 5 - Press the A button to turn off the DVR. The red LED flashes for 3 times quickly to confirm the
shutdown.
continuous Recording
Continuous recording takes up a lot of storage space, but it is sometimes necessary when, for
example, the uninterrupted audio recording is important, even if there is no motion in front of the
lens. In continuous recording, the DVR records Factory consecutive files from 3 minutes (can be
changed in configuration). To continuously record proceed as follows:
1 - Allow the start of the motion recording as above. The red LED flashes three times slowly. 1 - Allow the start of the motion recording as above. The red LED flashes three times slowly.
2 - Stop motion recording, press the D button on the remote. The LED returns to solid green, 2 - Stop motion recording, press the D button on the remote. The LED returns to solid green, 2 - Stop motion recording, press the D button on the remote. The LED returns to solid green,
indicating that the appliance is on standby waiting for commands.
3 - Press the B button to start the recording continues. The LED flashes green for 2 times slowly. 3 - Press the B button to start the recording continues. The LED flashes green for 2 times slowly.
This signals the start of the continuous recording.
4 - To stop continuous recording, press the B button on the remote again. The LED returns to solid 4 - To stop continuous recording, press the B button on the remote again. The LED returns to solid 4 - To stop continuous recording, press the B button on the remote again. The LED returns to solid
green, indicating that the appliance is on standby waiting for commands
5 - Press the A button to turn off the DVR. The red LED flashes for 3 times quickly to confirm the 5 - Press the A button to turn off the DVR. The red LED flashes for 3 times quickly to confirm the
shutdown.
Take pictures
DK-WP2 can also take pictures based on commands from the remote control. The photos are
saved in JPG format with 2560x1920 resolution (5MP) To take pictures, proceed as follows:
1 - Allow the start of the motion recording as above. The red LED flashes three times slowly. 1 - Allow the start of the motion recording as above. The red LED flashes three times slowly.
2 - Stop motion recording by pressing the D button on the remote. The LED returns to solid green, 2 - Stop motion recording by pressing the D button on the remote. The LED returns to solid green, 2 - Stop motion recording by pressing the D button on the remote. The LED returns to solid green,
indicating that the appliance is on standby waiting for commands.
3 - Press the C button to take the picture. The LED flashes red for the first time. This signals that 3 - Press the C button to take the picture. The LED flashes red for the first time. This signals that
the photo was taken and stored in memory. The solid green LED returns at last to report the
stand-by condition.
4 - Press the A button to turn off the DVR. The red LED flashes for 3 times quickly to confirm the 4 - Press the A button to turn off the DVR. The red LED flashes for 3 times quickly to confirm the
shutdown.
Viewing files on PC
To review and manage files recorded by the DVR
you can use a computer and a