3
1.2 Antenna
NOTE
: You must match the antennas to the frequency you will be using.
The antenna for the LINKS2450 is
not supplied. For optimum performance of the
LINKS2450, use a quality antenna system, such as model SLA-532, available from
SafeLink Corporation. This 5/8 over 5/8 wave high performance antenna offers
features specifically designed for security radio installations.
• 5dB gain two-piece mast with center coil
• Standard frequency 419.0625MHz, 440 to 470MHz
• Ten feet of coax with BNC connector attached.
To ensure proper operation, mount the antenna at least ten feet from the LINKS
2450 unit. (See diagram below).
14
RESET LINKS2450 PROGRAMMING TO
Section 6
FACTORY DEFAULT
If you need to reset the LINKS2450 to factory default programming, follow the
directions in the appropriate sections below.
6.1 Reset the LINKS2450 on a PC1575/1580 Panel
To reset the LINKS2450 on a PC1575/1580 panel, enter [96] [Installer’s Code] [96].
6.2 Reset the LINKS2450 on a PC5015 v2.2, PC5010 v2.0,
PC1555/1565 or PC580/585 Panel
To reset the LINKS2450 on a PC5015 v2.2, PC5010 v2.0 or PC1555/1565 panel,
enter [993] [Installer’s Code] [993].
NOTE
: This command is unavailable on PC5010 v1.0. If v1.0 is used, you must
perform a hardware reset (see section 6.3 below).
6.3 Perform a Hardware Reset (All panels)
To reset the LINKS2450 when connected to a PC5010 v1.0 or a PC4010/4020
panel, you must perform a hardware reset. To do this:
1.
Remove all power from the LINKS2450
2.
Short jumper J3
3.
Remove all wires from the YEL and GRN terminals
4.
With a piece of wire, short the YEL terminal to the GRN terminal
5.
Apply power to the LINKS2450 for 5 seconds.
6.
Remove power from the LINKS2450
7.
Reconnect all original wiring and re-power the LINKS2450
NOTE
: If the LINKS2450 is connected to a PC4010/4020 panel, the programming
done in the panel software will not be reset. See section 3.2, step 5 for information
on re-programming the PC4010/4020 sections.
3
1.2 Antenna
NOTE
: You must match the antennas to the frequency you will be using.
The antenna for the LINKS2450 is
not supplied. For optimum performance of the
LINKS2450, use a quality antenna system, such as model SLA-532, available from
SafeLink Corporation. This 5/8 over 5/8 wave high performance antenna offers
features specifically designed for security radio installations.
• 5dB gain two-piece mast with center coil
• Standard frequency 419.0625MHz, 440 to 470MHz
• Ten feet of coax with BNC connector attached.
To ensure proper operation, mount the antenna at least ten feet from the LINKS
2450 unit. (See diagram below).
14
RESET LINKS2450 PROGRAMMING TO
Section 6
FACTORY DEFAULT
If you need to reset the LINKS2450 to factory default programming, follow the
directions in the appropriate sections below.
6.1 Reset the LINKS2450 on a PC1575/1580 Panel
To reset the LINKS2450 on a PC1575/1580 panel, enter [96] [Installer’s Code] [96].
6.2 Reset the LINKS2450 on a PC5015 v2.2, PC5010 v2.0,
PC1555/1565 or PC580/585 Panel
To reset the LINKS2450 on a PC5015 v2.2, PC5010 v2.0 or PC1555/1565 panel,
enter [993] [Installer’s Code] [993].
NOTE
: This command is unavailable on PC5010 v1.0. If v1.0 is used, you must
perform a hardware reset (see section 6.3 below).
6.3 Perform a Hardware Reset (All panels)
To reset the LINKS2450 when connected to a PC5010 v1.0 or a PC4010/4020
panel, you must perform a hardware reset. To do this:
1.
Remove all power from the LINKS2450
2.
Short jumper J3
3.
Remove all wires from the YEL and GRN terminals
4.
With a piece of wire, short the YEL terminal to the GRN terminal
5.
Apply power to the LINKS2450 for 5 seconds.
6.
Remove power from the LINKS2450
7.
Reconnect all original wiring and re-power the LINKS2450
NOTE
: If the LINKS2450 is connected to a PC4010/4020 panel, the programming
done in the panel software will not be reset. See section 3.2, step 5 for information
on re-programming the PC4010/4020 sections.