DSC LINKS 2150, Installation Manual

Page: 6 / 12

6
LINKS2150 Programming Sections
These sections will only be available if a LINKS2150 v1.4W is connected to the Keybus.
[20] Module Configuration
Module configuration is set using Zone Lights as
shown below. After you enter section [20], the
options that are “on” will be shown either by the
corresponding zone light being on (LED keypads) or
the zone number being displayed (LCD keypads).
Press the corresponding number key to turn an option
ON or OFF. When finished, press [#].
Zone Light 1
ON - Communications Enabled - The
LINKS2150 will initiate communications for
all events that the panel has reporting
codes programmed for.
OFF - Communications Disabled - The
LINKS2150 will not initiate communications
for events that the panel has reporting
codes programmed for. Disable
communications to test the system.
Zone Light 2
OFF - TRBL OUT Normally High Impedence - If
there are no trouble conditions detected by
the LINKS2150, the TRBL OUT terminal will
be high-impedence. The TRBL OUT
terminal will switch to ground when the
LINKS2150 detects a trouble condition.
ON - TRBL OUT Normally Low - If there are no
trouble conditions detected by the
LINKS2150, the TRBL OUT terminal will be
low (ground). The TRBL OUT terminal will
switch to high-impedence when the
LINKS2150 detects a trouble condition.
Zone Light 3 to Zone Light 8 - For Future Use
[30] Call Direction Options
Program which of the following reporting code types
the LINKS2150 will send to the central station. Press
the number corresponding the the appropriate option
to turn the reporting type ON or OFF. When finished,
press [#].
Option
1 Alarm/restore reporting
2 Tamper/restore reporting
3 Opening/closing reporting
4 System maintenance reporting
5 System test transmission reporting
In most installations, you should program the tranmission of
alarm/restore reporting codes only. Your radio network has
limited bandwidth and capacity. The more signals each
LINKS2150 transmits, the fewer LINKS2150s you will be
able to install on your network.
[86] LINKS2150 Programming Sections
for PC1580
or
[803] LINKS2150 Programming Section
for PC5010, PC5015, PC5008, PC1565,
PC1565-2P, PC585
[01] 2150 Account Code
This 4-digit code is used to identify the system and is
transmitted when the LINKS2150 initiates
communications. Program a 4 digit code in this
section using only numbers from 0 to 9.
Note: An account number must be entered in this
section before communications through the
LINKS2150 can be used. Do not enter Hexadecimal
numbers in this section.
[10] Maintenance Alarm Reporting Codes
Program 2 digit reporting codes for each of the
following reporting codes
• Internal Low Voltage
This code will be sent when the voltage supplied
to the LINKS2150 on the 12+ and 12 - terminals is
less than 10.5 V
DC
for more than 4 minutes
• External AC Trouble
This code will be sent when the AC TRBL input
terminal is switched to ground.
• External Low Battery Trouble
This code will be sent when the LB TRBL input
terminal is switched to ground.
• Control Panel Connection Trouble
This code will be sent when connection is lost to
the panel on the Keybus for more than 60
seconds
• Test Transmission
This code will be sent at the same interval as the
test transmission of the panel.
[11] Maintenance Restoral Reporting Codes
Program 2 digit reporting codes for each of the
following reporting codes
• Internal Low Voltage
This code will be sent when the voltage supplied
to the LINKS2150 ion the 12+ and 12 - terminals
is restored to more than 11.6 V
DC
for more than 4
minutes
• External AC Trouble
This code will be sent when the AC TRBL input
terminal is switched to ground.
• External Low Battery Trouble
This code will be sent when the LB TRBL input
terminal is switched to ground.
• Control Panel Connection Trouble
This code will be sent when connection is
restored to the panel on the Keybus for more
than 60 seconds.