12
HSPA(3G)/Dual Alarm Communicator Installation Manual
The programming sections described in this document can be viewed at the keypad LCD. To start
programming enter:
[*][8][installer code] [851] [section number]
, where section number is the 3
digit section number referenced in this section. The programming worksheets at the end of this
document can be used to record the new values when programming changes have been made from
the default values.
NOTE:
Ethernet/cellular programming sections accessed through the panel are for
display pur-
poses only
. Configuration changes must be done using C24 Communications.
Red and Yellow
LEDs flashing
together
N/A
Initialization
Sequence
• The unit is still initializing please wait while the unit gets its programming and
establishes a connection to all programmed receivers.
Note: This process may take several minutes to complete.
Only Green
LEDs flashing
N/A
Hardware
Default Jumper • The hardware default jumper is installed and must be removed. See Figure 3.
Green LEDs
alternating
N/A
Radio Reset or
Radio Initializa-
tion
• If this status persists and the yellow LED shows 5 flashes, confirm that
the SIM card is active.
E
THERNET
/C
ELLULAR
P
ROGRAMMING
O
PTIONS
Table 8: Trouble indications
Trouble
indication
Trouble
Indicator
Digit
Possible
Causes
Trouble Possible Solution
System Options
[001] Ethernet IP Address
Default (000.000.000.000)
|____|____|____||____|____|____||____|____|____||____|____|____|
[002] Ethernet IP Subnet Mask
Default (255.255.255.000)
|____|____|____||____|____|____||____|____|____||____|____|____|
[003] Ethernet Gateway IP Address
Default (000.000.000.000)
|____|____|____||____|____|____||____|____|____||____|____|____|
[004] Receiver Supervision Interval
Default (0087/135) Valid range: 0000 - FFFF.
|____|____|____|____|
[005] System Toggle Options
|____| [1] Ethernet Receiver 1 Supervised Default (OFF).
|____| [2] Cellular Receiver 1 Supervised Default (OFF).
|____| [3] Supervision Type Default (OFF).
|____| [4] Primary Communications Path.
Default [OFF] TL2803G(R); [ON] 3G2080(R).
|____| [5] Redundant Communications Default (OFF).
|____| [6] Remote Firmware Upgrade Default (ON).
|____| [7] Alternate Test Transmission Default (OFF).
|____| [8] Cellular Low Signal Trouble Default (OFF).
[006] System Toggle Options 2
|____| [1] Ethernet Receiver 1 Enabled Default (ON).
|____| [2] Ethernet Receiver 2 Enabled Default (ON).
|____| [4] Cellular Receiver 1 Enabled Default (ON).
|____| [5] Cellular Receiver 2 Enabled Default (ON).
|____| [7] DLS Over Cellular Default (ON).
|____| [8] Network Trouble Suppression Default (OFF).
[007] DNS Server IP 1
Programming not permitted on UL/ULC listed sys-
tem.
Default (000.000.000.000)
|____|____|____||____|____|____||____|____|____||____|____|____|
[008] DNS Server IP 2
Programming not permitted on UL/ULC listed sys-
tem.
Default (000.000.000.000)
|____|____|____||____|____|____||____|____|____||____|____|____|
Programming Options
[010] System Toggle Options 3
|____| [1] Reserved
|____| [2] Visual Verification Default (OFF).
|____| [3] Reserved
[011] Installer Code
Default (CAFE) Valid range: 0000 - FFFF.
|____|____|____|____|
[012] DLS Incoming Port
Default (0BF6/3062) Valid range: 0000 - FFFF.
|____|____|____|____|
[013] DLS Outgoing Port
Default (0BFA/3066) Valid range: 0000 - FFFF.
|____|____|____|____|
[015] DLS Call-Up IP
Default (000.000.000.000)
|____|____|____||____|____|____||____|____|____||____|____|____|
E
THERNET
/C
ELLULAR
P
ROGRAMMING
W
ORKSHEETS
