DIRECTIONS FOR USE:
Switch the unit ON.
The word “
7
GAUSS” will display on the screen. When pressing the button
“GO!”the screen will display “
7
R.P.M”and pressing a second time the word
“
7
CHRONO”.
GAUSS reading:
In order to enter the programme to read magnet gauss you must press the button “Go!” during two seconds
when the word “GAUSS” is displayed on the screen
S 0000 GAUSS
or
N 0000 GAUSS
The letters “S” and “N” correspond to the magnetic poles being measured.
The DS-Pocket Checker is now ready to receive information.
Place the Pocket Checker’s Gauss sensor touching the magnet/motor you
want to verify, and then move the device all around the magnetic influence
zone searching for the highest reading. The highest reading will remain on
the screen in order to memorise it if required, this data will disappear if the
Pocket Checker is moved away from the magnet/motor
(photo 1)
.
Data Recording:
When you have the gauss information on the screen, press “Go!” button for two seconds (until the scre-
en goes blank). When you stop pressing, the screen will display “MEMORY” 1, subsequently pressing
“GO!”will display “MEMORY 2”, “MEMORY 3”, “MEMORY 4”, “MEMORY 5” and “OUT”.
Set the unit to the MEMORY you want to record the data to and again press the “Go!” button for two
seconds (until the screen goes blank), the data record will be saved into MEMORY and then the program-
me will quit automatically from this function.
In order to consult the data recorded, keep pressing the “Go!” button for two seconds (until the screen goes
blank) and then release, the screen will display the memory screen. If you want to quit, press the “Go!” button
again for two seconds in “out” mode.
¡ATTENTION!:
Always quit this way, or memory data can be lost or change.
R.P.M. reading:
Connect the R.P.M. reader sensor to the Pocket Checker.Pressing the button “Go!” for two seconds when
the screen shows the word “
7
R.P.M.” in order to enter the R.P.M. reading programme.
0.0 R.P.M.
Place the tip of the sensor 2 or 3mm away from the point at which we want to read the r.p.m.
In order that the sensor can take a reading, there must be a colour difference on the surface to be mea-
sured. We recommend reading on a black surface, for instance, tyres or crown gears…to do this you can
place a white sticker or paint a segment of it white (you can use the well known “Tippex” eraser) the white
section must be a quarter of the total diameter of the surface to be read.
(See photos 2 and 3)
.
Memorising R.P.M.:
Once you want to record the r.p.m.
displayed on the screen press the
“Go!” button for two seconds (until the
screen goes blank) and follow the
same directions as you did to memo-
rise GAUSS.
® “DS Electronic Racing Products” and its logotype is a registered trademark.
© “DS Electronic Racing Products”. All rights reserved. May 2003
“DS Electronic Racing Products” are in constant development, and the features of their pro-
ducts may be altered without warning.
¡
All “DS Electronic Racing Products” have one year warranty!.
Desde 1 hasta 5 memorias
Desde 1 hasta 5 memorias
IBB Auto Racing S.L.
C/ St. Joan Baptista, 79
08700 IGUALADA Barcelona (Spain)
Tel.: 93 803 08 80 · Fax: 93 805 50 57
www.ibbautoracing.com
Model Road Racing Cars Ltd.
P. O. Box 790 St. Helier JE4 0SW
JERSEY (Great Britain)
Fax Int. + 44 (0) 1534864988
www.mrrc.com [email protected]
2
3
1
CHRONO reading:
This option will allow you to read and record the timing between two points on a given track section.
You will need a device with double sensor in order to use this function.
(The device will be available shortly).
Distributed:
International Sales:
