background image

LIMITED WARRANTY

Dealer, warrants to the original consumer purchaser that each new SL27 Laminator which proves 
defective in materials or workmanship within the applicable warranty period will be repaired or, at our 
option, replaced without charge upon its return as outlined below.  The applicable warranty shall be one 
year from date of purchase.  “Original consumer purchaser” means the purchaser who  first purchased the 
product covered by this warranty other than for purpose of resale.
Liability for breach of any warranty express or implied shall be limited to the repair or replacement, at 
dealer, option, of the defective item.  Dealer shall not be liable for damages arising out of, or in connec-
tion with the use or performance of any product.  Any implied warranty shall be limited in duration to the 

duration of this warranty.  Some states do not allow limitations on how long an implied warranty lasts for 
the exclusion or limitation of consequential damages, so the above limitation may not apply to you.
There are no consumer serviceable parts in the SL27 Laminator.  If you require service under this 
Warranty, contact your dealer to obtain Return Authorization (RA), pack the product in its original packag-
ing (or request the same from Technical Service when requesting the RA), and include a description of 
the malfunction and proof of date of purchase.  Technical Service will arrange for the SL27 Laminator to
be picked up by a freight company. Failure to return in original packaging could void this warranty.
The Warranty extends to and is enforceable only by the original consumer purchaser, and only for the 
period which the product remains in the possession of the original equipment purchaser.  This Warranty 
does not cover any defect or malfunction due to the use of faulty non- SL27 Laminator materials, 

  .

e

c

n

a

n

e

t

n

i

a

m

 

y

r

a

s

s

e

c

e

n

 

d

n

a

 

e

l

b

a

n

o

s

a

e

r

 

e

d

i

v

o

r

p

 

o

e

r

u

li

a

r

o

 ,

e

n

i

h

c

a

m

 

e

h

f

o

 

e

s

u

b

a

 

r

o

 

e

s

u

 

e

l

b

a

n

o

s

a

e

r

n

u
This Warranty gives you speci fic legal rights and you may have other rights, which vary, from state to 
state.

12

Summary of Contents for DRYLAM SL



















Reviews: