background image

STREET USE 

- In most states, it is illegal for use on public roads. Do not operate 

this wheelchair on roadways, streets or any surfaces with vehicular traffic.

MOTOR  VEHICLE  SAFETY 

- Wheelchair conforms to the requirements of 

ANSI/RESNA WC/VoL.1-Section 19. The wheelchair has been dynamically 

tested in a forward facing mode and it must be forward facing during transport. 

Use with approved vehicle-installed restraining system that includes both pelvic 

and shoulder belts. This reduces the possibility of head and chest impacts with 

vehicle components. Postural supports and belts may be used in a moving 

vehicle but should not be relied upon to replace vehicle-installed restraining 

system that have been designed and tested for this purpose. 

HEADREST 

EXTENSION AND FIVE-POINT HARNESS MUST BE USED TO CONFORM 

TO ABOVE REQUIREMENTS.

STABILITY

 - Wheelchair is designed to be safe and stable as long as center of 

gravity is maintained. Care must be taken while performing activities that shift 

your center of gravity in the chair. Never reach so far that it requires shifting 

your body in the seat or leaning over out of the chair. When reaching for 

objects that require change of body position, posture or weight distribution, 

be certain front casters are positioned in a forward position and engage wheel 

locks. This will extend the wheel base and stabilize the chair. Do not lean over 

or apply weight to the top of the wheelchair back as it can increase the risk a 

fall or tip-over. When trying to extend arms over back, only reach as far as your 

arm can extend without having to alter your seating position.

RAMPS  AND  SLOPES

 - Be sure of your own capabilities, limitations and 

strength before attempting to go up a ramp. Correct techniques on ramp 

negotiation should be shown to you by a qualified professional. Do not use 

your chair on a slope steeper than 10% without assistance. Do not turn or 

change direction on a slope and always stay in the center of the ramp. If you 

must stop on an incline, make certain to avoid sudden, abrupt movement when 

you resume movement. Never use rear wheel locks to try to slow or stop your 

chair. This could result in your chair veering out of control.

Cautions

Summary of Contents for Wallaby













Reviews: