DriSteem Ultra-sorb XV Installation, Operation And Maintenance Manual Download Page 40

Form No. US-XV-IOM-EN-0518
Part No. 890000-190 Rev C

TWO-YEAR LIMITED WARRANTY

DRI-STEEM Corporation (“DriSteem”) warrants to the original user that its products will be free from 
defects in materials and workmanship for a period of two (2) years after installation or twenty-
seven (27) months from the date DriSteem ships such product, whichever date is the earlier.
 If any DriSteem product is found to be defective in material or workmanship during the applicable 
warranty period, DriSteem’s entire liability, and the purchaser’s sole and exclusive remedy, shall 
be the repair or replacement of the defective product, or the refund of the purchase price, at 
DriSteem’s election. DriSteem shall not be liable for any costs or expenses, whether direct or 
indirect, associated with the installation, removal or reinstallation of any defective product. The 
Limited Warranty does not include cylinder replacement for electrode steam humidifi ers or media 
replacement for Wetted Media Systems. 

DriSteem’s Limited Warranty shall not be effective or actionable unless there is compliance with 
all installation and operating instructions furnished by DriSteem, or if the products have been 
modifi ed or altered without the written consent of DriSteem, or if such products have been subject 
to accident, misuse, mishandling, tampering, negligence or improper maintenance. Any warranty 
claim must be submitted to DriSteem in writing within the stated warranty period. Defective 
parts may be required to be returned to DriSteem. Excluded from the Limited Warranty are all 
consumable and wear and tear items such as cylinders, membranes, fi lters, or media replacements. 
These items are subject to usual wear and tear during usage.

DriSteem’s Limited Warranty is made in lieu of, and DriSteem disclaims all other warranties, 
whether express or implied, including but not limited to any IMPLIED WARRANTY OF 
MERCHANTABILITY, ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, any 
implied warranty arising out of a course of dealing or of performance, custom or usage of trade.
DriSteem SHALL NOT, UNDER ANY CIRCUMSTANCES BE LIABLE FOR ANY DIRECT, INDIRECT, 
INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED 
TO, LOSS OF PROFITS, REVENUE OR BUSINESS) OR DAMAGE OR INJURY TO PERSONS OR 
PROPERTY IN ANY WAY RELATED TO THE MANUFACTURE OR THE USE OF ITS PRODUCTS. The 
exclusion applies regardless of whether such damages are sought based on breach of warranty, 
breach of contract, negligence, strict liability in tort, or any other legal theory, even if DriSteem has 
notice of the possibility of such damages. 

By purchasing DriSteem’s products, the purchaser agrees to the terms and conditions of this Limited 
Warranty.

EXTENDED WARRANTY

The original user may extend the term of the DriSteem Limited Warranty for a limited number of 
months past the initial applicable warranty period and term provided in the fi rst paragraph of this 
Limited Warranty. All the terms and conditions of the Limited Warranty during the initial applicable 
warranty period and term shall apply during any extended term. An extended warranty term of 
an additional twelve (12) months or twenty four (24) months of coverage may be purchased. The 
extended warranty term may be purchased until eighteen (18) months after the product is shipped, 
after which time no extended warranties are available. When a Dristeem humidifi er is purchased 
with a DriSteem RO system, an extended twenty-four (24) month coverage is included.

Any extension of the Limited Warranty under this program must be in writing, signed by DriSteem, 
and paid for in full by the purchaser.

DRI-STEEM Corporation

a subsidiary of Research Products Corporation
DriSteem is an ISO 9001:2008 certifi ed company

U.S. Headquarters:
14949 Technology Drive
Eden Prairie, MN 55344
800-328-4447 or 952-949-2415
952-229-3200 (fax)

European offi ce:
Marc Briers
Grote Hellekensstraat 54 b
B-3520 Zonhoven
Belgium
+3211823595 (voice)
+3211817948 (fax)
E-mail: [email protected]

Continuous product improvement is a policy of 
DriSteem Corporation; therefore, product 
features and specifi cations are subject to 
change without notice.

DriSteem and Ultra-sorb are registered 
trademarks of Research Products Corporation 
and are fi led for trademark registration in 
Canada and the European community.

Product and corporate names used in this 
document may be trademarks or registered 
trademarks. They are used for explanation only 
without intent to infringe.

© 2018 Research Products Corporation

Expect quality from the industry leader

For more than 45 years, DriSteem has been 
leading the industry with creative and reliable 
humidifi cation solutions. Our focus on quality is 
evident in the construction of Ultra-sorb steam 
dispersion panels, which feature stainless steel 
construction. DriSteem also leads the industry 
with a Two-year Limited Warranty and optional 
extended warranty. 

For more information

www.dristeem.com
[email protected]

For the most recent product information 
visit our Web site: www.dristeem.com

WARRANTY

Summary of Contents for Ultra-sorb XV









































Reviews: