background image

SETUP AND CONFIGURATION

Object list

Table 17-1:
Object List

Property

Description

Range/Type

R/W

Device Object

APDU_Timeout

Time between retransmissions in milliseconds. This device does not support 

retransmissions, so this always reads as “0”.

0

R

App Software Version

Controller Firmware Version (assembled by firmware) 

XX.XrYY (“X” = version; “Y” = revision)

String

R

Database_Revision

Increases if the settings change

16 bit

R

Daylight_Savings_Status

Daylight savings status of host controller

True/False

R

Description

Description of controller or location

32 Bytes

R/W

Device Address Binding

Address binds

List

R

Firmware_Revision

BACnet Firmware Revision

String

R

Local_Date

Date of host controller in format YYYY-MM-DD-DOW

YYYY-MM-DD-DOW

R

Local_Time

Time of host controller in format HH:MM:SS

HH:MM:SS

R

Max APDU Length Accepted

The maximum APDU length supported by this device is 480.

16 bit

R

Max Info Frames

The value specifies the maximum number of information frames the node 

may send before it must pass the token.

1

R/W

Max_Master

Number of the highest addressed node

1…127

R/W

Model_Name

“X2-abcde-BAC” (assembled by firmware)

a = number of loops

b = number of passive inputs

c = number of universal inputs

d = number of binary outputs

e = number of analog outputs

String

R

Number_of_APDU_Retries

Number of retransmissions. This device does not support retransmissions, 

so this always reads as “0”.

0

R

Object_Identifier

Device object identifier (CO06…CO09)

22 bit

R/W

Object_Name

Name of device

32 Bytes

R/W

Object_Type

The value is always “Device” for the device object

10 bit

R

Protocol_Objects_Supported

The enumeration of the supported object types

List

R

Protocol_Services_Supported

The enumeration of the supported services

List

R

Protocol_Version

BACnet protocol version number

1

R

Protocol_Revision

BACnet protocol revision number

14

R

Segmentation_Supported

This device does not support segmentation, so this always reads as “NO_

SEGMENTATION (3)”.

0…3

R

System_Status

Current physical and logical status supported: 

• OPERATIONAL (0)
• DOWNLOAD_REQUIRED (2) (IF INT. EEPROM CONF. ERRORS)
• NON_OPERATIONAL (4) (IF INT. I2C BUS ERRORS)

0…5

R

UTC_Offset

Offset to UTC time in case UTC time synchronization is used

-780…780

R/W

Vendor_Identifier

561

R

Vendor_Name

Vector Controls GmbH

String

R

Object_List

List of all objects currently implemented in the device

List

R

17

DRISTEEM TCI AND TRI2 HUMIDISTAT INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

Summary of Contents for Humidistat TRI2

























Reviews: