manualshive.com logo in svg

Drill Master 91938, Owner'S Manual & Safety Instructions

Share
Download
Drill Master 91938 Owner'S Manual & Safety Instructions Download Page 9

Page 9

For technical questions, please call 1-888-866-5797.

Item 91938 

        

SAFET

y

Op

ERA

TION

M

AINTENANCE

SETU

p

5.  Remove the Socket Head Bolt (54), 

the Flange Washer (96), the Outer Flange (55), and 

the cut-off wheel (sold separately).  See 

Figure C.

Socket Head 

Bolt (54)

Flange  

Washer (96)

Outer  

Flange (55)

Cut-Off Wheel

Inner Flange (57)

Figure C:  Cut-Off Wheel Hardware

6.  Replace with a new cut-off wheel, and reassemble 

the parts listed above in number 5.  The concave 

side of the Outer Flange (55) must face the 

wheel.  While holding the Lock Pin (63), tighten the 

Socket Head Bolt (54) with the Hex Key (111a).

7. 

LOOSEN THE BOLT (112) and make sure 

that the Swing Guard (53) moves freely 

back into place before operation.

Depth Adjustment

Note:

 The Cutting Depth will need to be 

adjusted whenever a worn down wheel 

is replaced with a new one.

1.  Loosen the Nut (15) on the Depth 

Adjustment Bolt (16) shown in 

Figure D

.

Depth  

Adjustment

Bolt (16)

Nut (15)

Figure D:  Depth Adjustment

2.  Turn the Depth Adjustment Bolt (16) to change 

the depth so that the wheel will not contact 

the base at any time during cutting.

3.  After adjustment, tighten the Nut (15) against the 

Bracket (14) to lock the adjustment in place.

Tool Set Up (cont’d)

Summary of Contents for 91938

















Reviews:

No comments

Brands by name

Popular brands

Load more brands