Dri-Eaz Velo F504-230V, Owner'S Manual, Page: 2 / 2

07-01844A F504/F505-230V 2013-10 Warranty 07-00427 2 Dri-Eaz Products, Ltd.
OPERATING INSTRUCTIONS
Note that the Velo and Velo Pro can be placed in a variety of
positions for drying and air circulation. See Fig. B for details.
1. Unwrap the cord and plug the unit into a standard 230V
outlet. CAUTION: Be sure switch is in the off position before
connecting unit to power outlet.
2. Direct the Velo outlet toward the surface to be dried.
3. Press On switch
4. When surface is dry to the touch, switch the unit off and
reposition the unit in the next area to be dried.
5. When finished, unplug the unit and re-wrap the cord in a
clockwise direction around the front and rear cord wrap tabs
and secure with the hook-and-loop provided.
Note: The Velo Pro includes a kilowatt hour meter, useful for
tracking electrical consumption. See Fig. D.
For additional instructions about the use of airmovers for
restorative drying, visit
www.DriEaz.co.uk and www.RSA-HQ-
UK.co.uk .
Transport and Storage
Always use the handle to load or carry the unit.
Wrap cord in a clockwise direction under front Cord Wrap tab
and rear bottom edge (Fig. A). Pull cord snug and secure with
hook-and-loop tie.
Units may be stacked for transport and storage.
When transporting in a vehicle, secure the unit(s) carefully to
prevent sliding and damage to the unit and/or injury to vehicle
occupants.
Keep unit dry. Do not expose the unit to rain or snow.
Maintenance
WARNING: Unplug unit before performing any maintenance.
Before each use
Inspect the power cord. If cord is damaged, do not use. Always
grasp the plug (not the cord) to unplug.
As needed
Clean housing and impeller. If dust accumulation is visible,
remove the four screws from the top, then turn the unit on its top
and remove the six fasteners from the bottom as shown (Fig. C).
Lift off the housing. Clean impeller assembly with a soft cloth. Do
not apply liquids to the impeller assembly. The housing may be
cleaned with a mild solution of detergent and warm water. Do not
use a hose to clean the unit. Ensure housing is completely dry
before reassembling.
FOR SERVICE CALL Dri-Eaz on
+44 (0)1908-611-211
.
SPECIFICATIONS
Model Velo (F504-230V) Velo Pro (F505-230V)
Weight 9.52 kg 9.52 kg
Dimensions
(D × W × H)
61 × 45.7 × 22.9 cm 61 × 45.7 × 22.9 cm
Amp draw .53 amps (230V) .53 amps (230V)
Power 124W 124W
Max. Airflow 1190 m
3
/h 1190 m
3
/h
RPM 1280 1280
Rotation Clockwise Clockwise
Static pressure 28 mm (H
2
O) 28 mm (H
2
O)
Sound level (avg.) 65 dB 65 dB
Control On/Off switch On/Off switch
Cord length 4.6 m 4.6 m
Fan 6 blades 6 blades
Kickstand No Yes
Kilowatt Hour
Meter
No Yes
Construction
Rotomolded
polyethylene and
injection molded ABS
housing components;
steel wire inlet and
outlet grills. Rotomolded
polyethylene and
injection molded ABS
housing components;
steel wire inlet and
outlet grills.
Safety CE CE
Specifications are subject to change without notice. Some values
may be approximate.
Fig. D: Pro model only: Kilowatt Hour
meter
To disassemble for
cleaning,
first remove the
four screws from the
impeller assembly 1)
(below), then turn the unit
on its top and 2) remove
the six screws from the
base. Lift off the housing.
Retain screws and
washers for reassembly.
1. Remove impeller
assembly screws (×4).
2. Remove base
screws (×6) and
lift out housing.
Fig. C: Disassembly