13
13
Assembly
ALWAYS BE SURE THE TOOL IS
IN THE “0” POSITION BEFORE
CHANGING ACCESSORIES, CHANGING COLLETS OR
SERVICING YOUR CORDLESS ROTARY TOOL.
SHAFT
LOCK
BUTTON
TO LOOSEN
TO TIGHTEN
COLLET
NUT
COLLET
COLLET
NUT
IDENTIFICATION
RINGS
480 0.32 cm
COLLET
481 0.24 cm
COLLET
482 0.16 cm
COLLET
483 0.08 cm
COLLET
!
WARNING
COLLET IDENTIFICATION CHART —
Collet sizes can
be identified by the rings on the back end of collet.
0.08 cm Collet has one (1) ring.
0.16 cm Collet has two (2) rings.
0.24 cm Collet has three (3) rings.
0.32 cm Collet has no rings.
COLLET
WRENCH
COLLET —
To loosen, first press shaft lock button and
rotate the shaft by hand until the lock engages the shaft
preventing further rotation.
Do not engage lock while the
Rotary Tool is running.
With the shaft lock engaged use the collet wrench to
loosen the collet nut if necessary. Change accessories
by inserting the new one into the collet as far as possi-
ble to minimize runout and unbalance. With the shaft
lock engaged, finger tighten the collet nut until the
accessory shank is gripped by the collet. Avoid exces-
sive tightening of the collet nut.
COLLETS —
Four different size collets (see illus-
tration), to accommodate different shank sizes, are
available for your Cordless Rotary Tool. To install a dif-
ferent collet, remove the collet nut and remove the old
collet. Insert the unslotted end of the collet in the hole
in the end of the tool shaft. Replace collet nut on the
shaft.
Always use the collet which matches the shank
size of the accessory you plan to use.
Never force a
larger diameter shank into a collet.
BALANCING ACCESSORIES —
For precision work, it is
important that all accessories be in good balance
(much the same as the tyres on your car). To true up or
balance an accessory, slightly loosen collet nut and
give the accessory or collet a 1/4 turn. Retighten collet
nut and run the Tool. You should be able to tell by the
sound and feel if your accessory is running in balance.
Continue adjusting in this fashion until best balance is
achieved. To maintain balance on abrasive wheel
points, before each use, with the wheel point secured
in the collet, turn on the Cordless Rotary Tool and run
the 415 Dressing Stone lightly against the revolving
wheel point. This removes high spots and trues up the
wheel point for good balance.
Operation Instructions
!
CAUTION
Introduction
The Cordless Rotary Tool is a handful of high-speed
power. It serves as a carver, a grinder, polisher, sander,
cutter, power brush, drill and more.
Your Cordless Rotary Tool has a small, powerful electric
motor, is comfortable in the hand, and is made to accept
a large variety of accessories including abrasive wheels,
drill bits, wire brushes, polishers, engraving cutters,
router bits, and cutting wheels. Accessories come in a
variety of shapes and permit you to do a number of
different jobs. As you become familiar with the range of
accessories and their uses, you will learn just how
versatile your Cordless Rotary Tool is. You’ll see dozens
of uses you hadn’t thought of before now.
The real secret of the Cordless Rotary Tool is its speed.
To understand the advantages of its high speed, you
have to know that the standard portable electric drill
runs at speeds up to 2,800 revolutions per minute. The
typical electric drill is a low-speed, high torque tool; the
Cordless Rotary Tool is just the opposite — a high-
speed, low torque tool. The chief difference to the user
is that in the high speed tools, the speed combined with
the accessory mounted in the collet does the work. You
don’t apply pressure to the tool, but simply hold and
guide it. In the low speed tools, you not only guide the
tool, but also apply pressure to it, as you do, for example,
when drilling a hole.
13