Draper PT142K, User Manual, Page: 9 / 18

7. UNPACKING & CHECKING
9
7.1 PACKAGING
Carefully remove the multi-tool from the packaging and examine it for any sign of damage
that may have happened during shipping. Lay the contents out and check them against the
parts shown below. If any part is damaged or missing; please contact the Draper Helpline
(the telephone number appears on the Title page) and do not attempt to use the product.
The packaging material should be retained at least during the guarantee period: in case the
machine needs to be returned for repair.
Warning! Some of the packaging materials used may be harmful to children. Do not leave
any of these materials in the reach of children.
If any of the packaging is to be thrown away, make sure they are disposed of correctly;
according to local regulations.
7.2 WHAT´S IN THE BOX?
As well as the multi-tool; there are several parts not fitted or attached to it.
8. BASIC MULTI-TOOL OPERATIONS
8A
Flexible shaft
Collets x3
Collet spanner/ plain slot
screwdriver
Bristle brush
Holder for
cutting/sanding/grinding
discs
Holder for felt polishing
wheels.
Diamond grinding point x3
Holder for large sanding
drum
Holder for small sanding
drum
HSS drill bits (2.0, 2.4 &
3.0mm) x3
Brass wheel
Large felt polishing wheel x5
Small felt polishing wheel x5
Cut off wheel (Ø 22mm x 1mm) x25
Fine polishing disc (600 Grit-green) x12
Sanding disc (180 Grit-red) x10
Large sanding drum (120 Grit) x8
Small sanding drum (120 Grit) x8
Aluminium oxide grinding point x10
Sharpening stone
NOTE: To ensure safe use do not use the polishing wheels faster than 25,000rpm:
When you purchase additional accessories check the safe working speed is compatible with
the tool.
8.1 ACCESSORY INSTALLATION/ REPLACEMENT
- FIG. 1
This Multi-Tool is designed for use with 1.9, 2.3 & 3.0mm
shank accessories only.
WARNING: Use bits of the correct shank diameter suitable
for the speed of the tool.
Selection of the correct accessory, suitable for the
intended application is vital. Seek guidance if uncertain of
selection.
Press the spindle lock button
and unscrew the collet
nut using the spanner supplied.
Choose from the collets provided, the appropriate size for
the accessory shank. If the size is not known insert the bit
into the collet. The collet which offers a machine fit to the
shank is the correct one to use. Do not force the bit into
the collet.
Place the collet into the spindle before loosely replacing
the collet nut
.
Slide the accessory in as far as possible before tightening
the collet nut. Press the spindle lock button
and
tighten the collet nut with the spanner provided to lock
the bit in place. If the accessory seems loose, reduce the
collet size to ensure the bit is secured correctly.
NOTE: Do not overtighten the collet nut
To lock the spindle inside the flexible shaft
, pull back
on the colar .
8.2 FITTING FLEXIBLE DRIVE SHAFT -
FIGS. 2 - 3
Remove collar . Depressing spindle lock button and
loosen the collet nut. Install the 3.0mm collet and loosely
replace the collet nut.
Insert the flexible drive shaft rod
into the collet
chuck and lock. Screw the drive shaft collar onto
housing.
8.3 SWITCHING ON AND OFF - FIG. 4
Press switch into the 'I' position. This will start the
machine. Press switch to the 'O' position - this will stop the
machine.
Using the variable speed dial
will enable you to alter
the speed of the collet chuck:
Position 1 - SLOW
Position 3 - MEDIUM
Position 6 - FAST
Select the correct speed for the work and type of bit you
are using.
FIG.1
FIG.2
FIG.3
FIG.4
-
Collets x5 changed to Collets x3 29/07/14 AN