Connect the painting cup complete with material. Before operating ensure the air
pressure and material to be sprayed is suitable for this product. Do not connect
air hose until you are absolutey ready to begin work.
• The paint quantity sprayed maybe increased or decreased using the fluid
control knob
✪✌
, Fig.1.
• The spray pattern maybe adjusted from a round pattern to a fan pattern
turning
the knob
✫✌
, Fig.1 left or right. For the fan pattern the operating pressure may
have to be increased slightly.
• Hold the gun at a right angle to the working surface and move it parallel.
• Keep the gun about 6-10 inches away from the surface (depending on the
material and operating pressure), see Fig.2.
• Start the stroke before squeezing trigger and release it just after ending the
stroke.
• Always keep the material deposited even and wet.
• Operate at the correct air pressure for a fine finish and safe performance.
Never exceed the maximum operating pressure.
WARNING WHEN SPRAYING:
• Do not spray in enclosed areas and maintain good ventilation.
• Never spray close to or in the proximity of a naked flame.
• Always use suitable eye protection.
• Wear an appropriate face mask.
OPERATION
WHY USE HVLP ?
HVLP (High Volume Low
Pressure) spraying
equipment has been
developed as a result of the
introduction of the
Environmental Protection Act
1990. This legislation is aimed at
cutting solvent emissions
produced from both commercial
and car refinish products.
HVLP equipment uses less
air (less the 10psi, 0.69 bar at
the air cap), but with a higher
throughput resulting in more
paint staying on the workpiece
and less being released into the
atmosphere. With traditional
spray guns there is a
tendency for the automized
paint and solvent to bounce off
the workpiece and pollute the
atmosphere.
HVLP SPRAY GUN
STOCK No.54436/54437.
PART No.HVLP2/HVLP3.
Operating air pressure ....................22 to 38psi/1.5–2.6 bar
Air consumption....................................................14-17cfm
Air inlet .....................................................................
1
⁄
4
" BSP
Cup capacity:
HVLP2 ..............................................1 Litre
HVLP3 ...............................................600cc
Nozzle:
HVLP2..............................................1.9mm
HVLP3..............................................1.5mm
Weight:
HVLP2..............................................1048g.
HVLP3................................................762g.
SPECIFICATION
DECLARATION OF
CONFORMITY
We Draper Tools Ltd. Declare under our sole
responsibility that the product:
Part No:-
HVLP2/HVLP3.
Stock No:-
54436/54437.
Description:-
Spray gun.
To which this declaration relates is in conformity with the
following directive(s):-
89/392/EEC, 91/368/EEC, 93/44/EEC and 93/68/EEC.
With reference to EN414 (point 8), EN292.1(4.9), EN292.2(3.6).
J.N. DRAPER
Managing Director
10/97
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE SAFE AND
EFFECTIVE USE OF THIS TOOL.
This spray gun is manufactured from quality materials and carefully checked by the manufacturer before its despatch.
To get the best from this quality product read the following instructions carefully before operating your spray gun.
• It is advisable to lubricate the needle with oil at the beginning of the working day. The operation is quite simple and it
increases its durability and working order.
• Never remove nozzle No.2 with universal pliers, only use the hexagonal wrench, take care not to damage the nozzle.
• The ideal working pressure is stated in the above specification table. It can vary though, according to the density of the
paint.
NOTE: Maximum operating pressure 38psi (2.6 bar).
CORRECT
INCORRECT
15-25cm
(6-10 inch)
Fig.2.
Fig.3.
Fig.5.
Fig.4.
Fig.1.
HIGH PRESSURE
HVLP
FLUID
LINE
AIR
LINE
AIR
SUPPLY
PRESSURE TANK
WIDER
SPRAY
PATTERN
NORMAL
SPRAY
PATTERN
NARROW
SPRAY
PATTERN
45
º
ROUND JET
VERTICAL JET
HORIZONTAL JET
6"
8"
05/98
