Stock Nos. .......................................................... 30586, 30587
Part Nos. ........................................................... ALG33, ALG34
Air supply pressure min ................................ 6.9 bar (100lbf-in
2
)
Air supply pressure max ............................. 13.8 bar (200lbf-in
2
)
Pressure range ....................................... 0-9.6 bar (0-138lbf-in
2
)
Air inlet ....................................................
1
/
4
" BSP taper (female)
Hose length ....................................................... 0.5M (approx.)
Accuracy ......................... EC directive (only bar scale approved)
FOR USE IN VEHICLE WORKSHOPS AND TYRE FITTING
BAYS. NOT RECOMMENDED FOR USE ON AIRCRAFT TYRES
ALWAYS WEAR EAR & EYE PROTECTION
Draper air tools have been carefully tested and inspected before shipment and are
guaranteed to be free from defective materials and workmanship for 6 months
from the date of purchase except where tools are hired out when the guarantee
period is ninety days from the date of purchase.
Should the machine develop any fault, please return the complete tool to your
nearest authorized warranty repair agent or contact Draper Tools Limited,
Chandler’s Ford, Eastleigh, Hampshire, SO53 1YF. England.
Telephone (023) 8049 4344.
If, upon inspection it is found that the fault occurring is due to defective materials
or workmanship, repairs will be carried out free of charge. This guarantee does not
apply to normal wear and tear, nor does it cover any damage caused by misuse,
careless or unsafe handling, alterations, accident, or repairs attempted or made by
any persons other than the authorized Draper warranty repair agent.
This guarantee applies in lieu of any other guarantee expressed or implied and
variation of its terms are not authorized.
Your Draper guarantee is not effective unless you can produce upon request a
dated receipt or invoice to verify your proof of purchase within the guarantee
period.
Please note that this guarantee is an additional benefit and does not affect your
statutory rights.
- IMPORTANT:
Prior to installation of the air line gauge ensure
the air supply line is clear and drain off the compressor tank
and pipework. Connect the air line gauge to a pressure
vessel (tyre) and actuate the calibrated indicator assembly
approximately 10 operations up/down scale.
- ACCURACY: (EC DIRECTIVE 86/217)
This air line gauge has been calibrated in its normal working
position on test equipment with an accuracy that is traceable
to the UK National Standard through the National Physical
Laboratory Reference 08010/C4/1/P383 via a system of
calibration which includes Dead Weight Tester, Serial
No.4361, Piston Unit No.:A890. Dead Weight Tester
calibrated at Theta Systems Ltd. - Namas Laboratory No.409.
MODEL No.
DESCRIPTION
PART No.
STOCK No.
ALG33
Hose & connector ass'y
YRHA2121
30769
ALG34
Hose & connector ass'y
YRHA2122
30770
ALG33
Twin hold connector
YC01A03
30771
ALG34
Single clip-on connector
YC02E03
30773
ALG33/34
Valve ass'y
YSAS4115
30764
1. Always wear safety goggles or glasses.
2. Always ensure machine is switched off before connecting to air
supply.
3. Disconnect any machine from the air supply before changing
blades or discs, and before servicing any type of machine.
4. Always keep your air tool clean and lubricated. Daily lubrication is
essential to avoid internal corrosion and possible failure.
5. Do not wear watches, rings, bracelets or loose clothing when using
air tools.
6. Using only light weight coil hoses from a tool to the wall or
compressor coupling. Do not fit quick change couplings onto the
machine as vibration can cause the coupling to fail.
7. Do not overload the machine. Allow the tool to operate at its
optimum speed for maximum efficiency.
8. Do not increase the air pressure above the manufacturer's
recommended level, as excessive overload can cause the machine
casing to split. Also this creates excessive wear on moving parts
and possible failure.
9. In the interests of safety and possible damage to the
machine/operator, always ensure that the machine has stopped
before putting it down after use.
10. Always ensure that the workpiece is firmly secured leaving both
hands free to control the machine.
11. Always ensure that the accessories such as blades, discs, sockets,
etc. are rated/designed for use with the machine. Also correctly
and securely fastened before connecting the machine to the air
supply.
- AIR SUPPLY:
Tools in the range generally operate at a maximum
pressure of 13.8 bar (see specifications) and this should be
controlled via a combined regulator/water separator such
as the Draper 4222/4 unit which with proper
maintenance will ensure a constant supply of dry air at all
times. See Fig.1. Always check tool operating pressure
before use.
Water in the compressor tank will cause serious corrosion
to your air tools and should be drained daily to avoid
excessive water in your air supply. Dirty wet air rapidly
shortens the life of your air tool.
If you are using an air tool on a hose over 25ft. long it is
advisable to increase the bore of the hose to the next larger size available ie.1⁄4" increases 3⁄8". This will ensure adequate pressure and
volume of air to power the tool.
- OPERATION (Fig.1):
Air tools without inbuilt regulators vary the pressure on your air supply regulator.Push or clip the connector accordingly over the valve
to take the pressure reading. To inflate, fully depress the trigger and release to take the new pressure reading. To deflate, slightly
depress the trigger. Air will be heard to be escaping while this position is maintained. Remove connector from valve and replace valve
cover if applicable.
- NOTE:
Observe manufacturer's inflation levels. Do not use on toy inflatables as damage will occur.
FIG.1
Leader Hose.
Quick Coupling.
Recoil Hose.
Nipple.
Nipple.
Regualtor.
Water Separation.
Drain Daily.
Air Supply.
To your
Air Tool.
Do not install Quick
Coupling here.
SPECIFICATION
GUARANTEE
ASSEMBLY
OPERATING INSTRUCTIONS
GENERAL SAFETY RULES
FOR AIR TOOLS PRODUCTS
