Access MultiView Installation/Operating In struc tions
page 3 of 4
Wiring Diagrams for Optional Built-in Controls
Adjustments (Screen Motor)
Screen has been factory set and sho
u
ld not normally req
u
ire f
u
rther adj
u
st-
ment. Howe
v
er, if yo
u
desire to change the “
u
p” and “down” stopping positions,
proceed as follows:
CAUTION:
Be s
u
re all switches are in “off” position before adj
u
sting limit
switches. Always be prepared to sh
u
t screen off man
u
ally when new adj
u
st-
ment is being tested. Screen may be se
v
erely damaged if s
u
rface is allowed
to r
u
n too far
u
p or too far down.
“DOWN” LIMIT SWITCH
—Down stopping position can be adj
u
sted by t
u
rn-
ing the white socket (located on the motor end of screen roller). T
u
rning the
socket co
u
n ter clock wise will allow the roller to r
u
n farther down. T
u
rning it
clockwise will shorten op er a tion, ca
u
sing it to stop sooner. One f
u
ll re
v
ol
u
-
tion of the socket will alter the stopping position of the
v
iewing s
u
rface by
approximately 1
1
/
4
".
“UP” LIMIT SWITCH—
Up stopping position can be adj
u
sted by t
u
rning the
yellow socket (located on motor end of screen). T
u
rning the socket co
u
n ter -
clock wise will allow the roller to r
u
n farther
u
p. T
u
rning it clockwise will ca
u
se
the roller to stop sooner. One f
u
ll re
v
ol
u
tion of the socket will alter the stopping
position of the
v
iewing s
u
rface by approximately 1
1
/
4
".
AT NO TIME SHOULD SURFACE BE UNROLLED ENOUGH TO EXPOSE
ANY PART OF SCREEN ROLLER.
Built-in Lo
w
V
oltage Control
Junction
b
ox at
left end of screen
Internal screen
w
iring
W
hite (
N
eutral)
Black (Hot)
Green (Ground)
Dashed
w
iring
b
y electrician
110v AC supply
N
L1
Built-in
V
ideo Interface Control
Junction
b
ox at
left end of screen
Internal screen
w
iring
W
hite (
N
eutral)
Black (Hot)
Green (Ground)
Dashed
w
iring
b
y electrician
110v AC supply
Trigger signal
V
IC115 (115
V
AC,
w
hite cord & plug)
V
IC12 (12
V
DC,
b
ro
w
n & orange leads)
N
L1
Adjustments (Masking Motor)
Screen has been factory set and sho
u
ld not normally req
u
ire f
u
rther adj
u
st-
ment. Howe
v
er, if yo
u
desire to change the “
u
p” and “down” stopping positions,
proceed as follows:
CAUTION:
Be s
u
re all switches are in “off” position before adj
u
sting limit
switches. Always be prepared to sh
u
t screen off man
u
ally when new adj
u
st-
ment is being tested. Screen may be se
v
erely damaged if s
u
rface is allowed
to r
u
n too far
u
p or too far down.
“DOWN”
LIMIT SWITCH—Down stopping position can be adj
u
sted by t
u
rning
knob #2 (on motor end of masking roller). T
u
rning the knob co
u
nterclockwise
will allow the roller to r
u
n farther down. T
u
rning it clockwise will shorten opera-
tion, ca
u
sing it to stop sooner.
“UP” LIMIT SWITCH—
Up stopping position can be adj
u
sted by t
u
rning knob
#1 (on the motor end of masking roller). T
u
rning the knob co
u
nterclockwise
will allow the roller to r
u
n farther
u
p. T
u
rning it clockwise will ca
u
se the roller to
stop sooner.
www
.draperinc.com
(765) 9
8
7-7999
