220V Access by Draper
page 4 of 4
Wiring Diagrams (continued)
www.draperinc.com
(765) 987-7999
MC1
3 Button Wall Switch
DOWN - Black
COM - White
UP - Red
White or Blue-Common to screen & 110/220V AC Neutral
Red-to screen (directional)
Brown-to screen (directional)
Yellow-to 110/220V AC-Hot
Black-to 110/220V AC-Hot
Green/Yellow (Ground)
Eye Port
for IR Eye, RF Receiver or LED
Wall Switch. For more than one of
these, a splitter is required.
Aux Port
for connecting additional LVC-III
modules (up to six total can be linked-
connect from Aux to Eye).
Dashed wiring by electrician
Low voltage wiring by others
White/Blue (Common)
Red 110/Black 220 (Up)
Black 110/Brown 220 (Down)
Location of key
operated on-off
switch if furnished
To
110/220V
Line
Internal Screen Wiring
STOP
Control
Switches
24v DC
STOP
Green/Yellow
(Motor Ground)
RS232 Data FROM Control System
RS232 Data TO Control System
Signal Ground & Manual Switch Common
Manual Switch Down
Manual Switch Up
White or Blue-Common
Red-to Screen (directional)
Black-to Screen (directional)
Brown-Hot to AC
Green/Yellow-Ground
Fuse
Program LED
Eye Port for IR Eye. For RF Receiver or LED
Wall Switch, a Splitter and a Power Supply
is required. Plug RF Receiver or LED Wall
Switch and Power Supply into splitter, then
run cable from Splitter to MC1 Eye Port.
Low Voltage Wiring by others
AC Wiring by electrician
MC1
Location of key
operated on-off
switch if furnished
To AC Line
White/Blue (Common)
Red 110/Black 220 (Up)
Black 110/Brown 220 (Down)
Internal Screen Wiring
Green 110V/
Green/Yellow 220V
(Motor Ground)
Built-In VIC-12*
Built-In VIC-115*
Green/Y
ello
w
Blac
k
Blue
Green/
Yellow
Black
Brown
Blie
Ground
#2 Up
#1 Down
Common
Jacketed Motor Cable
220 VAC
Screen Motor
Ring Terminal on each Ground Wire
with Star Washer screwed to Spine
HSG.
Cap
HSG.
Plug
2
5
1
115 Volt Relay
Wire connected with Quick Disconnect
: : : :
Brown
Black
:
:
:
:
:
:
:
:
::
::
::
::
::
::
4
6
8
7
3
Blac
k Lead
Blue Lead
Green/
Yellow
Green/Y
ello
w
Blac
k
Blue
Green
Yellow
Green/Yellow
Black
Brown
Blue
Ground
#2 Up
#1 Down
Common
Jacketed Motor Cable
220 VAC
Screen Motor
Ring Terminal on ground wire
riveted to J-Box with Star Washer
HSG.
Cap
HSG.
Plug
: : : :
: : : :
: : : :
Bro
wn (-)
Or
ange (+)
14 13
9
5
1
12 Volt (VIC-12) or 6 Volt (VIC-6) Relay
Wire soldered to terminal
Wire connected with Quick Disconnect
: : : :
Black
Brown
*These wiring diagrams are for Access screens with motor on audience left (standard), and fabric unrolling from the back of the roller (standard).
See separate Serial Communication-RS232 Instruction sheet for enabling
RS232 with the MC1.
External Low Voltage and Wireless
12.7
mm
R 6.4
mm
9.5
mm
35
mm
3.2
mm
38
mm
4.8
mm
R3.2
mm
6.4
mm
8
mm
8
mm
4.8
mm
6.4
mm
32
mm
114
mm
122.2
mm
197
mm
228.6
mm
28.6
mm
Mounting Bracket Dimensions
UP 5V COM DWN
U
P
D
O
W
N
C
O
M
M
O
N
5V
Motor Data Cable
plugged in here
ILT Switch-to-Motor—Dry Contacts or Data Cable connection
Please Note:
This Splitter/
Jack is located inside the junc-
tion box of your Access XL
screen.
Back of wall switch.
Please Note:
Although both
Dry Contact and Data Cable
connections are shown, you
should only use one connec-
tion type per motor.
Data Cables to switches or
to additional motors can
be plugged into any of the
three open jacks. If this is a
"Case First, Screen Later"
installation, plug the motor
cable into the jack indicated
in the drawing.
