Dragonfly Ultra White Installation Manual Download Page 4

© 2018 Dragonfly

Fixed Projection Screen Manual

181015-1400

4

10

4

7

5

2

12

11

9

8

1

3

6

Step 6A

Step 6B-C

Fabric 

Edge

Step 4

Step 3

Step 5

Step 3. Assemble the Frame

A.  Slide the short frame sections into the long frame sections.
B.  Insert the 8 frame corner screws into all 4 corners of the 

frame and loosely tighten to hold the frame together.

C.  Hand-tighten all four screws, ensure the corners are 

square, then tighten the screws completely.

D.  Lift up and set aside to prepare screen material for assembly.

Step 4. Prepare the Screen Material

A.  Lay the protective sheet out on the work surface, and 

clean the surface and work area to avoid staining the 
screen material.

B. 

Put on the supplied gloves before handling the screen 
material.

C.  Roll the screen material out onto the protective sheet, 

then lay the frame down onto the material, ensuring the 
corners of the frame and fabric are properly aligned as 
shown in Step 4.

D.  Insert frame rods into the edges of the screen as shown 

in step 4.

Step 5. Attach the Screen Material to the Frame

A.  Align the springs to the holes in the screen fabric.
B.  Using the spring tool, attach the springs to the screen 

material, following the numbering in the image to the 
right, ensuring screen and frame stay aligned with 
corners. Once the corners are connected, work around 
the screen attaching the remaining springs.

C.  Ensure all springs are installed straight and 

perpendicular to the screen. Any springs installed at 
an angle may cause ripples in the screen material.

Step 6. Install Brackets and Frame Bezels

A.  With the film screen still laying face down, lay the thin 

bezel caps on to the respective horizontal and vertical 
edges of the screen. The aluminum side should be facing 
up with fabric edges facing out. Refer to Image 6A.

i.  The tracks on the back of the thin bezel caps align for 

a tight fit in each of the corners. Refer to image 6B.

B.  Once the thin bezel frames are in place and aligned, 

install the thin bezel frame brackets.

i.  10 total brackets will be used to tighten all 4 thin 

bezel caps in place. 2 brackets for each of the 
vertical frames and 3 brackets for each of the 
horizontal frames.

C.  Hook curved end of the thin bezel bracket to the 

outermost track of the thin bezel cap and align it with 
a sliding nut. Use the M5x6mm screws to tighten.

Note:

 There are 4 additional sliding nuts on the horizontal 

frames, 2 on each side. These sliding nuts are used to 

install the wall brackets.

B

x32

C

Summary of Contents for Ultra White









Reviews: