Draco UVS-1, Operating Instructions

Page: 2 / 2

, JMS, 2-12-2011
Spareparts for UVS-1
R e p l a c i n g / A d j u s t i n g t h e K n i f e
Before working on machine disconnect from power
supply by removing plug from socket.
Wear protective glasses!
Replacing the Knife
Clamp the machine in a vice on the clamping surfaces SV
between aluminium protective jaws.
Before working on machine disconnect from power
supply by removing plug from socket. Ware protective
glasses!
Loosen the screws 21 . Remove the support roller 25 (option).
Unscrew the screws 21 and remove the spring plate 20 .
Remove the spring 19 . Remove the Circlip ring 16 and washer 17 .
Push back the knife pin 18 .
Do not interchange the spacers 18: the wrong spacing could
ruin the jaws and knife.
Insert a new knife 11 with the old spacers 15 . Insert the knife pin 18 .
Mount the washer 17 and the Circlip ring 16 .
Insert the spring 19 . Reassemble spring plate 20 and support roller 25 .
Replacing the Jaws
Loosen the screws 8 and remove the jaws 10 . Press out the positioning
pins 9. Mount new jaws and positioning pins. Tighten the screws 8 .
Adjusting the knife Clearance
For clearance between knife and jaws that is too large, loosen the
fillister head screw
5 . Adjust the clearance with the set screw 4 .
Retighten the fillister head screw 5 .
The knife must not rub on the jaws: Danger of breakage.
Note: If heavy burring is produced while cutting, repeat the adjustment.
Sharpening the knife/Jaws
The knife and the jaws must be sharpened and adjusted at the same
time.
This work should be performed by an authorised DRÄCO customer
service location. Send in the complete machine for this purpose.
Spareparts for UVS-1
Pos. Order Quantity Pos. Order Quantity
No. No. Description per Shear No. No. Description per Shear
1 10500 Head casting 1 42 81249 Securing washer A 4 3
1-52 15557 Shearhead UVS cpl. assembled,
without motor 1 43 81012 Flat fillister head screw M 4 x 20 3
51 81243 Securing washer A 5 2
3 81263 Hex socket screw M 4 x 16 1 52 81181 Hex socket screw M 5 x 20 2
4 81089 Spacing-block set screw M 5 x 10 1 53 10531 Holder for switch 1
5 81272 Flat fillister head screw M 4 x 22 1 54 15531 Screw 1
6 10002 Spacing-block 7,5 1 53-95 10055 Motor cpl. 230 V 1
8 81270 Flat head screw M 4 x 8 4 60 10015 Motor case bottom 1
9 81248 Positioning Pin 3x6 4 60 a 10515 Endcap case bottom 1
61 10016 Platespring 1
11-14 07014 Knife 1014S standard 1 62 10017 Motorcase top 1
07016 Knife 1014S serrated 63 10018 Rubber insulation 8 mm 1
64 10019 Switch lever 1
10 13574/1 Set of Jaws 1 65 10020 Switch pad 1
66 10021 Flat fillister head screw M 3 x 4 1
13 12000 Knife adjusting screw M 6 x 17 1 67 10024 Field 230 Volt 1
13-14 12222 Knife adjusting screw M6x17+lockring 1 69 10027 Condensator 1
14 12100 Knife Lockring M6 1 70 10028 Wire endcap 1
15 12400 Spacing shims 1 71 10029 Carbon brush holder 2
16 81275 Circlip 2 72 10030 Motor protective switch 1
17 81072 Washer A 6,4 2 73 10031 Switch 2-polig 1
16-18 12500 Knife pin 6 Ø 1 74 10032 Fillister head screw M 3 x 5 4
15-18 12555 Knife pin set (Pos. 15-18)
1 75 10033 Connection wire 1
19 12200 Spring 1 76 10036 Armature 230 Volt 1
20 12300 Spring cover 1 79 10038 Ball bearing 608-2 Z 1
21 81271 Flat head screw M 3 x 8 4 80 10039 Rubber ring AS 21, 3x2,4 1
24 17900 Knifepin bushing Ø 10 mm 2 83 10040 Ball bearing 626-2 Z/LZ 1
(24) 17911 Knifepin bushing Ø 11 mm (2) 84 10041 Rubber ring BS 18x45 1
25 10076 Support roller in metal (option) 1 85 10042 Spring washer 18,8/9,2 x 0,25 1
32-39 10080 Drive Shaft cpl. assembled 1 86 10043 Motor endcap 1
32 35556 Eccentric drive shaft 1 87 10044 Plastic cord clamp screw M10x11,5 1
33 13555 Ball bearing 6000/28Z 1 88 10045 Rubber-sleeve 1
34 10005 Sleeve 7x10x12 IR 2 89 32046 3 m cable with plug 1
35 10300 Needle bearing HK 1010 2 90 10047 Matal-screw Ø 4 x 16 mm 6
36 10450 Cap for needle bearing 1 91 10048 Filtercap 2
37 10006 Key 12 x 3 x 2 1 92 10049 Round-head screw M 3 x 10 2
38 10007 Gear 1 93 10050 Carbon brush 2
39 10009 Circlip 7 SP220 1 94 10051 Carbon spring 2
40 81239 Tap screw M 4 x 6 2 95 10052 Carbon cap screw 2
41 10010 Gear case 1
Optional assessories
10059 Adjustable guide S/01 100 mm
10060 Adjustable guide S/01 250 mm
10061 Adjustable guide S/01 500 mm
18000 Support roller (metal)
Specifications are subject to change for improvement without prior notice.
Max Draenert GmbH & Co.KG
Electric - Cordless - Pneumatic Tools - Machines
Germany
Administration D-73777 Deizisau P.O.Box 1120 Tel. +49-7153-8217-0
Production Shears D-73779 Deizisau Gutenbergstrasse 15-17 Fax +49-7153-8217-66
Internet
http://www.dracotools.com
E-mail:
draenert@dracotools.com