Draco PN 4361, Operating Instructions

Page: 2 / 2

KD, 16-3-2011
Spare parts for DRÄCO Profile Nibblers PN 4361 and PN 4360
Spare Part List DRÄCO Profile Nibblers PN 4361 and PN 4360
Version 2002
Pos. Order- Description Qty. Pos. Order- Description Qty.
No. No.
1-30 32300 Motor 230V with electronic 1 44 13039 Ball Bearing 1
1-30 32400 Motor 115V with electronic 1 45 41092 Backgear 2
1 32040 Motorhousing 1 51 41001 Retaining Ring 1
2 32047 Housing Cap until 2001 1 52 41002 Retaining Ring 1
2 32058 Housing Cap since 2002 1 53 41003 Grooved ball bearing 1
3 32050 Switch 1 54 41004 Fitting key 1
4 32054 Guide Piece 1 55 41005 Eccentric Shaft 1
5 32056 Switch Pad 1 56 41006 Needle Cage 1
6 32055 Pressure Spring 1 57 41007 Spring Ring 1
7 32044 Wire 2 58 41008 Grooved Ball Bearing 1
8 32042 Carbon Brush Set (2 piece) 1 59 41009 Needle Bearing 1
9 32041 Carbon Brush Holder 2 60 41010 Housing 1
10 32045 Condensator 1 61 41011 Cheesehead Screw 2
10 32059 Electronic speed control 1 62 41012 Grease Nipple 1
11 32046 Cable with Plug Europe 1 63 41013 Connecting Rod Pin 1
12 32522 Connection Cable 1 64 41014 Connecting Rod 1
13 32048 Screw 2 65 41576 Punch 1
14 32053 Screw 2 66 41016 Liner 1
15 32052 Cable Collar 1 67 41167 Extension Holder 1
16 32039 Field 230 V 1 68 41168 Lower Extension of Punch 1
16 32139 Field 115V 1 69 41169 Holder for PN 4360 1
17 32038 Air Deflector Ring 1 70 41577 Die 1
18 32036 Rubber Sleeve 1 71 41171 Punch Guide 1
19 32030 Ball Bearing 1 72 41022 Raised Head Screw 4
20 32037 Washer 1 73 41579 Wearing Plate 1
21 32033 Armature 230V 1 74 41174 Upper Extension of Punch 1
21 32133 Armature 115V 1 75 41091 Eccentric Shaft Gear 1
23 32032 Bearing Cover 1 76 41095 Washer 1
24 10038 Ball Bearing 1 77 41107 Gasket 1
25 32034 Securing Ring 1 78 41039 Set Screw 1
27 32014 Bearing End Plate 1 79 41119 Support for PN 4361 / AK 3161 1
28 32010 Screw 4 65-79 41175 Tool Set cpl. for PN4361 1
29 32043 Pin 1 42861 Transport Box for PN 4361
30 32012 Screw 2 18000 Transport Box for PN 4360+PN4320
31 32057 Label 1
Designated use
The DRÄCO Nibbler PN 4360 and PN 4361 are
electrically operated hand machines:
For separating sheets such as trapezoidal sheet,
corrugated sheet, boxed sheet, offset profiled
strips For separating work pieces made of a punch able
material such as steel, aluminium, non-ferrous heavy metal
and plastic. For nibbling straight or curved exterior and
interior cut-outs. For nibbling from scribed lines.
The nibbling process produces cutting edges free of
deformations.
Before putting the machine into service
1. Safe operation of the appliance is only possible if you
have completely read the operator's manual
2. Check the wear plate (73)
3. Check depth of immersion of the punch
4. The mains voltage must correspond to the information
on the machine type plate.
5. Machines designated for 230 V can also be connected
to 220 V power supplies.
6. Machines designated for 115 V can also be connected
to 110 V power supplies.
Advice for operation
Check tools hourly for wear.
Never work with blunt tools!
Otherwise the machine may be overloaded.
Do not approach the work piece with the
machine until the machine has been switched
on and reached maximum speed.
Cooling and lubrication
The cutting result is improved and the service life of
the punch increased if the cutting track is coated with
oil before machining the work piece.
Recommended for steel: Punching and nibbling oil, order no.
HW103387. Recommended for aluminium: Wisura oil, order
no. HW125874
Changing the cutting direction
For right/left-hand operation or if a sectional sheet is
to be machined, the tool and cutting direction can be
turned to the right or left.
•
Release the screw (78)
•
Turn the tool (67 or 69) to the desired direction
•
Turn on screw (78)
Interior cut-outs
Interior cut-outs require a start hole of at least 24 mm Ø.
Wear plate
The wear plate (73) protects the holder (79 or 69). Check
wear plate regularly and replace if worn.
Care and Maintenance
Before working on machine disconnect from
power supply by removing plug from socket.
Always keep the machine and the ventilation slots
clean.
Oil the knife pin and knife at regular intervals.
If the machine should happen to fail despite the care
taken in manufacture and testing, repair should be
carried out by an authorised customer services agent
for DRÄCO power tools
Environmental protection
Recycling raw materials instead of waste
disposal
Machine, accessories and packaging should be sorted
for environment-friendly recycling.
These instructions are printed on recycling paper
manufactured without chlorine
.
CE-Declaration of conformity
We declare under our sole responsibility that this product is
in conformity with the following standards.
EC 98/37, EC 93/ 68 EWG, EC 04/108 EC, or
standardisation documents DIN EN ISO 12100-1,
DIN EN ISO 12100-2, EN 50 144, EN 55 014
09 Max Draenert
Guarantee
Dräco tools carry a guarantee of 12 months from date of
delivery. Damage attributable to normal wear and tear,
overload or improper handling will be excluded from the
guarantee. In case of complaint please send the machine,
undismantled, to your dealer or the Dräco Service Centre for
electric power tools.