04
05
Installation
Installation environment
Installation method
Equipment must be installed in the following environments:
Open the packing box and check whether the main engine and accessories are in
good condition. If there is any defect, please inform your supplier immediately;
Connect the battery to the host, and select the appropriate massage head to
connect with the host.
·
·
·
·
·
·
·
Temperature:5℃
～
40℃;
Relative humidity
:≤
90%
;
Barometric pressure
:
70kPa
～
106kPa
;
Charger:IN:
100-240V ~50/60
Hz 0.6A
OUT:26V 1A
instrument
:
Rated voltage
：22.2V
Battery capacity
:2500
mAh
Test
After installing the battery and massage head, turn on the power switch and press the
“Start/Stop/Gear” button to observe whether the device is operating normally.
·
·
Equipment and accessories should be in good condition;
Operate the equipment according to the instructions and check the functions. If
the equipment can run normally, the product will pass the acceptance test.
Acceptance
·
·
·
·
·
·
·
·
·
·
·
·
Do not put batteries in water or wet them!
·
It is forbidden to charge the battery under the condition of fire source or extreme heat.
Do not use or store batteries near heat sources such as fires or heaters! If the battery
leaks or smells, it should be removed immediately from the vicinity of the open fire;
·
Please use a special charger;
·
Do not put batteries into fire or heat them;
·
It is forbidden to short circuit the positive and negative poles of batteries with
wires or other metal objects. It is forbidden to transport or store batteries with
necklaces, hairpins or other metal objects;
·
Do not use nails or other sharp objects to pierce the battery shell. Do not hammer
or pedal the battery!
·
Do not hit or throw batteries!
·
It is prohibited to decompose batteries in any way!
·
Do not place batteries in microwave ovens or pressure vessels!
·
If the battery emits odor, heat, distortion, discoloration or any other abnormal
phenomena, it should not be used; if the battery is in use or charging, it should be
immediately removed from the instrument or charger and stopped using!
·
·
·
·
·
Do not place any object in the ventilation hole of the product;
Do not immerse in water or let water enter the ventilation holes of the product;
Do not fall or improperly use;
Before each use, we should carefully check the operation status of the main engine,
batteries, chargers and so on to ensure that they can meet the normal use;
Do not change or modify the product in any way;
Never let the product run or charge in an unattended state;
The special charger provided by the manufacturer must be used for charging. It is
strictly forbidden to use other power supply equipment to charge the product;
It is forbidden to start the equipment during charging;
It is forbidden to plug the battery after the power switch is turned on;
It is forbidden to put equipment into fire;
Don't use it for more than one hour continuously. Let the equipment stop for 30
minutes before reusing.
About Batteries
About Charging
Before the first use, charge for about three hours and fill up the battery. When
charging, the device can be connected or disconnected;
When charging, the DC end of the special adapter is connected to the charging port
of the battery;
The battery icon on the battery flickers regularly, and the digital display of the
battery power indicates that the battery is being charged;
When the battery icon on the battery stops flickering and remains on, the digital
display shows that 100% of the battery is full;
Batteries can be charged at any time and at any level of electricity;
·
·
·
When the power is less than 20%, the power indicator digital tube flickers, please
charge it in time;
It is not recommended that the battery power be completely depleted to 20% level;
The average running time of the equipment is three hours, depending on the frequency
of vibration and the applied pressure during use.
DEEP MUSCLE MASSAGER
DEEP MUSCLE MASSAGER
