WIL-11560-E-08
5
PS220/230 Bolted Metal
SECTION 2
MATERIAL CODES
MODEL
XPS220 = PRO-FLO
®
SHIFT ATEX
THREADED PORTS
XPS230 = PRO-FLO
®
SHIFT ATEX
FLANGED PORTS
PS220 = PRO-FLO
®
SHIFT
THREADED PORTS
PS230 = PRO-FLO
®
SHIFT
FLANGED PORTS
WETTED PATH
A = ALUMINUM
S = STAINLESS STEEL
W = DUCTILE IRON
OUTER PISTON
A = ALUMINUM
S = STAINLESS STEEL
M = MILD STEEL
Z = NO OUTER PISTON
CENTER SECTION
AA = ALUMINUM
AIR VALVE
A = ALUMINUM
DIAPHRAGMS
BNS = BUNA-N (RED DOT)
EPS = EPDM (BLUE DOT)
FSL = FULL-STROKE SANITARY
SANIFLEX™, IPD [HYTREL
®
(CREAM)]
FSS = SANIFLEX™ [HYTREL
®
(CREAM)]
NES = NEOPRENE (GREEN DOT)
SSL = FULL-STROKE SANIFLEX™
IPD [HYTREL
®
(CREAM)]
TSS = FULL-STROKE PTFE
W/SANIFLEX™ BACK-UP
TWS = FULL-STROKE PTFE
W/WIL-FLEX™ BACK-UP
VTS = FKM (WHITE DOT)
WFS = WIL-FLEX™ [SANTOPRENE
®
(THREE BLACK DOTS)]
WWL= WIL-FLEX™ IPD
[SANTOPRENE
®
(THREE
BLACK DOTS)]
VALVE BALLS
BN = BUNA-N (RED DOT)
EP = EPDM (BLUE DOT)
FS = SANIFLEX™ [HYTREL
®
(CREAM)]
NE = NEOPRENE (GREEN DOT)
PU = POLYURETHANE (BROWN)
TF = PTFE (WHITE)
VT = FKM (WHITE DOT)
WF = WIL-FLEX™ [SANTOPRENE
®
(THREE BLACK DOTS)]
VALVE SEATS
A = ALUMINUM
M = MILD STEEL
S = STAINLESS STEEL
VALVE SEAT O-RINGS
BN = BUNA-N (RED DOT)
EP = EPDM (BLUE DOT)
FS = SANIFLEX™ [HYTREL
®
(CREAM)]
NE = NEOPRENE (GREEN DOT)
PU = POLYURETHANE (BROWN)
TF = PTFE (WHITE)
VT = FKM (WHITE DOT)
WF = WIL-FLEX™ [SANTOPRENE
®
(THREE BLACK DOTS)]
SPECIALTY CODES
0014 BSPT
0100 Wil-Gard 110V
0102 Wil-Gard sensor wire ONLY
0103 Wil-Gard 220V
0319 Single-port exhaust, BSPT
0320 Single-port exhaust
0391 25 mm (1
″
) NPT center-ported inlet and discharge manifold, CSA
0392 25 mm (1
″
) NPT side-ported inlet and discharge manifold, CSA
0480 Pump cycle monitor (sensor & wires)
0483 Pump cycle monitor (module, sensor & wires)
0485 Pump cycle monitor (module, sensor & wires), DIN flange
0492 U.L. Approved, Side-ported (1
″
inlet and discharge manifolds)
0493 U.L. Approved, Center Ported NPT, Turbo “drop-in”
(1
″
Inlet facing air inlet, 3/4" discharge facing exhaust)
0494 U.L. Approved, Center Ported NPT, Pro-Flo “drop-in”
(1
″
inlet facing exhaust, 3/4" discharge facing air inlet)
0504 DIN flange
0677 25 mm (1") NPT center-ported inlet and discharge manifold
0678 25 mm (1") BSPT center-ported inlet and discharge manifold
0687 25 mm (1") NPT center-ported inlet and discharge manifold,
Submersible Center Section
0688 25 mm (1") BSPT center-ported inlet and discharge manifold,
Submersible Center Section
0695 19 mm (3/4") NPT center-ported discharge manifold
(Turbo-Flo "Drop-in")
0696 19 mm (3/4") BSPT center-ported discharge manifold
(Turbo-Flo “Drop-in”)
0697 19 mm (3/4") NPT center-ported discharge manifold
(Pro-Flo “Drop-in”)
0698 19 mm (3/4") BSPT center-ported discharge manifold
(Pro-Flo “Drop-in”)
0730 25 mm (1") NPT side-ported inlet and discharge
0735 19 mm (3/4") NPT center-ported discharge manifold
(Turbo-Flo “Drop-in”), Submersible Center Section
0736 19 mm (3/4") BSPT center-ported discharge manifold
(Turbo-Flo “Drop-in”), Submersible Center Section
0737 19 mm (3/4") NPT center-ported discharge manifold
(Pro-Flo “Drop-in”), Submersible Center Section
0738 19 mm (3/4") BSPT center-ported discharge manifold
(Pro-Flo “Drop-in”), Submersible Center Section
NOTE:
Most elastomeric materials use colored dots for identification
NOTE:
Not all models are available with all material options
NOTE:
The Wilden UL 79-listed products covered by this manual are PS220 models and are defined by Specialty Codes. All materials may not be available
for UL-Listed pumps. Wilden UL-Listed pumps have been evaluated for use at a 25°C (77°F) ambient temperature with a maximum inlet pressure of
3.4 bar (50 psig).
PS220/230 METAL
LEGEND XPS 220 / X X X
X
X / X X X / X X / X X X / X X X X
25 mm (1") Pump
Maximum Flow Rate:
254 lpm (56 gpm)
O-RINGS
MODEL VALVE
SEATS SPECIALTY
VALVE
BALLS
CODE
DIAPHRAGMS
AIR VALVE
CENTER
SECTION
OUTER
PISTON
WETTED
PATHS
WILDEN PUMP DESIGNATION SYSTEM
(if applicable)