Dover PSG ALL-FLO IOM A025 Series Installation Operation & Maintenance Data Download Page 5

ALF-11010-E-02

All-Flo

5

PRINCIPLES OF OPERATION

The air-valve directs pressurized air behind the diaphragm on the right, 

causing the diaphragm on the right to move outward (to the right).
Since both the right diaphragm and the left diaphragm are connected  

via a diaphragm rod, when the right diaphragm moves to the right, the 

left diaphragm (through the action of the diaphragm rod) moves to the 

right also.
When the diaphragm on the left side is moving to the right, it is referred 

to as suction stroke. When the left diaphragm is in its suction stroke,  

the left suction ball moves upward (opens) and the left discharge ball 

moves downward (closes). This action creates suction and draws liquid 

into the left side chamber.

The air-valve directs pressurized air behind the left diaphragm, causing 

the left diaphragm to move outward (to the left).
Since both the left diaphragm and the right diaphragm are connected  

via a diaphragm rod, when the left diaphragm moves to the left, the  

right diaphragm (through the action of the diaphragm rod) moves to  

the left also.
When the diaphragm on the left side moves outward, the left discharge ball 

moves upward (opens) and the left suction ball moves downward (closes). 

This causes the liquid to leave the left side liquid outlet of the pump.
Simultaneously, the right diaphragm moves inward (to the left), which 

causes the right suction ball to open and the right discharge to close, 

which in turn causes suction, drawing liquid into the right chamber.
The process of alternating right suction / left discharge (and vice-versa) 

continues as long as compressed air is supplied to the pump.

HOW AN AIR OPERATED DOUBLE  

DIAPHRAGM PUMP WORKS

SECTION

3

Summary of Contents for PSG ALL-FLO IOM A025 Series





















Reviews: