Dover HEIL LIBERTY TP1L-SM-0520 Service Manual Download Page 107

Page: 107 / 136

Issued May 2020

Body Controller Software

BODY CONTROLLER SOFTWARE

101

PASSWORD PROTECTED SCREENS

To access password protected screens press and hold the OK button for 3 seconds.

This will switch the view to the password screen. Enter the password and press OK.

Passwords for Protected Screens:

Maintenance Screen: 4321

Option Settings Screen: 123412

Figure 42. Password Protected Screens

MAINTENANCE SCREEN

Service Mode is strictly intended to allow movement of the lift or packer blade while servicing or troubleshooting the unit.
Service Mode overrides all interlocks and disables all automated operation of the Packer and Lift.

Daily Pack Cycle count – reset with OK button

Daily Arm Cycle count – reset with OK button

Maintenance Hours – reset with OK button

Service Mode – activated with OK button

Figure 43. Maintenance Screen

Summary of Contents for HEIL LIBERTY TP1L-SM-0520










































































































Search results

Summary of Contents for HEIL LIBERTY TP1L-SM-0520

Reviews:

Related manuals for HEIL LIBERTY TP1L-SM-0520

Brands by name

Popular brands

Dover HEIL LIBERTY TP1L-SM-0520, Service Manual

Search results

Summary of Contents for HEIL LIBERTY TP1L-SM-0520

Reviews:

Related manuals for HEIL LIBERTY TP1L-SM-0520

Brands by name

Popular brands