Dover HEIL LIBERTY TP1L-SM-0520 Service Manual Download Page 106

Page: 106 / 136

Issued May 2020
Body Controller Software

Printed in the U.S.A.

BODY CONTROLLER SOFTWARE

100

CAB CONTROLLER OUTPUTS

Figure 41.Cab Controller Outputs

State of each output in brackets [ ].

All Outputs

[ON] - Output is On.

[OFF] - Output is Off.

Diagnostic features outputs 00 thru 07

[Disabled] - Output is disabled by option set or spare.

[Under Voltage on VBB] - Supply Voltage is too low.

[Over Voltage on VBB] - Supply Voltage is too high.

[Settings Invalid] - Program Error.

[Wire Break] - Open Circuits Detected

[Short Circuit] - Short Circuit Detected

[Over Current] - Overload on Circuit

Diagnostic features outputs 08 thru 15

[Disabled] - Output is disabled by option set or spare.

OUTPUT

PIN#

DESCRIPTION

OUT00

GRABBER CLOSE SOL

OUT01

GRABBER OPEN SOL

OUT02

PTO SOL

OUT03

PUMP1 SOL

OUT04

PUMP2 SOL

OUT05

LIFT ENABLE SOL

OUT06

SECONDARY CONTROL ENABLE

OUT07

SPARE OUTPUT 7

OUT08

IN CAB ALARM 1

OUT09

IN CAB ALARM 2

OUT10

OUT OF DIM SIG

OUT11

HOPPER CAMERA TRIGGER

OUT12

STROBE 1

OUT13

WORK LIGHT 2

OUT14

STROBE 2

OUT15

WORK LIGHT 1

Summary of Contents for HEIL LIBERTY TP1L-SM-0520










































































































Search results

Summary of Contents for HEIL LIBERTY TP1L-SM-0520

Reviews:

Related manuals for HEIL LIBERTY TP1L-SM-0520

Brands by name

Popular brands

Dover HEIL LIBERTY TP1L-SM-0520, Service Manual

Search results

Summary of Contents for HEIL LIBERTY TP1L-SM-0520

Reviews:

Related manuals for HEIL LIBERTY TP1L-SM-0520

Brands by name

Popular brands