background image

Step 3:  Backboard and Rim

4

Pro-645

rim

backboard

C.   Locate rim pad, peel off 

      adhesive and place on 

      backboard at rim location

D.  Assemble rim with enclosed   

      hardware

E.   Fasten rim cover under rim

F.   Hang Net

G.  Check leveling of pole.  Pole

      should be level in all 

      directions. 

Note:  If adjustment is 

necessary,  adjust system by 

rotating the nuts.  After system 

is level, completely tighten nuts.             

A.   Lower system to the safety stop.

B.   With three people, two people hold up

      the backboard and the third person 

      inserts:            2, 3-1/2" bolts

 

 

    2, 4-1/2" bolts

 

 

   12, 1/2" nylon washers

                                8, 1/2" steel flatwashers

                                4, 1/2" lock nuts

4-1/2" bolt

1/2" steel washer

1/2" nylon

1/2" nylon

1/2" steel washer

1/2" lock nut

1/2" nylon       

Step 4:  Height Adjustment Decal

Figure 9:  Backboard and Rim

NOTE:  All hardware for goal

is included in rim package.

3-1/2" bolt

1/2" steel washer

1/2" nylon

Turn handle

clockwise 

to lower

black

protective 

sleeve

mark 

here

Figure 10: 

Height Adjustment

Turn handle 

counter

clockwise 

to raise

height

labels

10’

A.   Raise system to 6’  from rim.  (Measuring 

       from top of rim to the ground.)

B.   With a marker, draw a line right above the sleeve 

      on the inside metal part of the crank system facing

      the pole so they won‘t peel off (See Figure 10).

      Note: Placing the decals on the front or sides of the 

      crank may cause them to peel off.

C.   Raise system to 7' from rim.

D.   Make another mark at edge of sleeve.

E.    Continue marking lines at 8’, 9’ and 10’    

F.    Place provided numerical decals on the galvanized 

      steel to align with the designated height 

      measurement marks. Note:  For accuracy, the black 

      line on the decal under the numbers should match 

      up with the determined marker height. 

G.  Height should now be set. Adjust if needed.

 Note:  Regulation rim height is 10 feet.

7’

8’

9’

6’

Summary of Contents for Pro-645

Page 1: ...safety please follow the instructions while assembling this system Proper and complete assembly is essential to ensure for the operation and safety of this system To reduce any serious injury this system should be properly installed maintained and operated Before beginning please read and understand the directions Suggested Tools and Materials 2 3 people Socket Wrenches 9 16 3 4 and 15 16 Open End...

Page 2: ...e 16 wide and 48 deep IMPORTANT Do Not proceed to Step F until concrete has cured A minimum of 72 hours Allow additional time for cold wet or humid weather WARNING Two person minumum required for Step F Not following this warning may resullt in an injury and or property damage post cap F Remove basketball pole from box and place post cap on the TOP of the pole G Place basketball pole onto the bolt...

Page 3: ...er In between both arms and the pole on both sides of pole place a 1 2 nylon On the other side of extension arm finish off with a 1 2 nylon 1 2 flat washer and a 1 2 lock nut C Locate top extension arm D Repeat Step B See Figure 5 for illustration upper extension arm 1 2 lock nut 1 2 flat washer 1 2 nylon 1 2 nylons 12 bolt 1 2 flat washer 1 2 nylon lower extension arm Figure 5 Extension Arms Figu...

Page 4: ...for goal is included in rim package 3 1 2 bolt 1 2 steel washer 1 2 nylon Turn handle clockwise to lower black protective sleeve mark here Figure 10 Height Adjustment Turn handle counter clockwise to raise height labels 10 A Raise system to 6 from rim Measuring from top of rim to the ground B With a marker draw a line right above the sleeve on the inside metal part of the crank system facing the p...

Reviews: