Dot Hill Systems AssuredSAN 6004 Cli Reference Manual Download Page 290

Page: 290 / 363

290 XML API basetype properties

network-parameters

This basetype is used by

show network-parameters

Table 46

network-parameters properties

Name

Type

Description

durable-id

string

Controller network port ID in the form

mgmtport_

controller-ID

active-version

uint32

Not applicable

ip-address

string

Controller network port IP address.

gateway

string

Controller network port gateway IP address

subnet-mask

string

Controller network port IP subnet mask

mac-address

string

Controller network port MAC address.

addressing-mode

string

•

Manual

: Obtain network address from manual (static) settings.

•

DHCP

: Use DHCP to obtain network address.

addressing-

mode-numeric

uint32

Numeric equivalents for

addressing-mode

values.

•

1: Manual

•

2: DHCP

link-speed

string

Not applicable.

link-speed-

numeric

uint32

Not applicable.

duplex-mode

string

Not applicable.

duplex-mode-

numeric

uint32

Not applicable.

auto-

negotiation

string

Not applicable.

auto-

negotiation-

numeric

uint32

Not applicable.

health

string

The health of the network connection.

•

Degraded

•

Fault

•

N/A

•

Unknown

health-numeric

uint32

Numeric equivalents for

health

values.

•

0: OK

•

1: Degraded

•

2: Fault

•

3: Unknown

•

4: N/A

health-reason

string

If Health is not

, the reason for the health state.

health-

recommendation

string

If Health is not

, the recommended actions to take to resolve the health issue.

Summary of Contents for AssuredSAN 6004












































































































































































































































































































































































Search results

Summary of Contents for AssuredSAN 6004

Reviews:

Dot Hill Systems AssuredSAN 6004, Cli Reference Manual, Page: 290 / 363

Search results

Summary of Contents for AssuredSAN 6004

Reviews: