manualshive.com logo in svg

Dot Hill Systems AssuredSAN 6004, Cli Reference Manual, Page: 172 / 363

Share
Download
Dot Hill Systems AssuredSAN 6004 Cli Reference Manual Download Page 172

172 Alphabetical list of commands

show network-parameters

Description

Shows the settings and health of each controller module’s network port.

Min. role

monitor

Syntax

show network-parameters

Output

IP Address

The network port IP address.

Gateway

The network port gateway IP address.

Subnet Mask

The network port IP subnet mask.

MAC Address

The controller’s unique Media Access Control address.

Addressing Mode

•

Manual

: Network settings set manually (statically).

•

DHCP

: DHCP used to set network parameters.

Link Speed

•

Unknown

: For a system operating in Single Controller mode, this controller module is not present. 

•

10mbps

: The network port link speed is set to 10 Mb/s.

•

100mbps

: The network port link speed is set to 100 Mb/s.

•

1000mbps

: The network port link speed is set to 1000 Mb/s.

Health

The health of the network connection.

•

OK

•

Degraded

•

Fault

•

N/A

•

Unknown

Health Reason

If Health is not 

OK

, this field shows the reason for the health state.

Health Recommendation

If Health is not 

OK

, this field shows recommended actions to take to resolve the health issue.

Example

Show network parameters for each controller module.

# show network-parameters

Basetypes •

network-parameters

•

status

See also •

set network-parameters

Summary of Contents for AssuredSAN 6004












































































































































































































































































































































































Reviews:

No comments