manualshive.com logo in svg

Dostmann Electronic P700, Operation Manual

Share
Download
Dostmann Electronic P700 Operation Manual Download Page 4

1.1 General advice 

• For cleaning the instrument please do not use

abrasive cleaner but a dry or wet piece of cloth.

• Please store the measuring instrument in a dry and

clean place.

• Avoid any force like shocks or pressure to the

instrument.

• Do not use force to connect the probe or interface

plugs in. The interface plug is different from the
probe plug.

• If no sensor is connected to the instrument while

switching on „open“ shows on the display (Please
refer to chapter error codes/troubleshooting).

• A retractable stand on the back of the instrument

allows it to be used as a bench top instrument. 

1.2 Operation

Before switching on the instrument, connect the
probe/s to the instrument and insert the battery
(Please refer to chapter 6. Power supply / battery
changing). A number on the instrument's housing
marks each port.

1.3 Switching on and off 

By operating the ON/OFF-key the instrument swit-
ched on or off. After switching on the instrument
indicates a full segment test for 1,5 sec., afterwards
the instrument shows the calibration-code and the
adjusted measurement category for channel 1. (Only
2-channel instruments: After additionally 1,5 sec. 
the instrument shows the calibration-code and the
adjusted measurement category for channel 2.) 
Then it starts operating in measurement mode in-
dicating the actual measurement value (for example:
temperature). All instruments display the measure-
ment value of channel 1 on the top display line (big
display line). Directly below you will see the trending
bargraph. The second channel of our 2-channel
instruments you will see on the bottom line (small
display line). 

Fig 1: 

Example of channel information after switching on.:

channel 1

Line 1: 

[oFF  P 

=  calibration code of channel 1

according to standard linearization (DIN), probe selec-
tion of channel 1 = Pt100.

channel 2

Line 2: 

[oFF  P  

= calibration code of channel 2 

according to standard linearization (DIN), probe selec-
tion of channel 2 = Pt100.

1. Handling

4

1

2

DE P700 Anleitung engl. 12/11  06.12.2011  10:04 Uhr  Seite 4

Summary of Contents for P700





























Reviews:

No comments

Brands by name

Popular brands

Load more brands