04
THANK YOU
for choosing this DÖRR quality product.
Please read the instruction manual and safety hints carefully before first use.
Keep this instruction manual together with the device for future use. If other people use this device, make
this instruction manual available. This instruction manual is part of the device and must be supplied with the
device in case of sale.
DÖRR is not liable for damages caused by improper use or the failure to observe the instruction manual and
safety hints.
GB
01 | SAFETY HINTS
•
Only for the illumination for photographic purposes. Not suited for permanent room lightning.
•
Ensure sufficient ventilation during operation. After use, please switch the device off and disconnect the
power connection.
•
Before replacing the bulbs please turn off power.
•
Protect the device from rain, moisture, direct sunlight and extreme temperatures.
•
Do not operate or touch the device with wet hands.
•
Protect the device against impacts. Do not use the device if it has been dropped. In this case a qualified elec-
trician should inspect the device before you use it again.
•
Do not attempt to repair the devise by yourself. When service or repair is required, contact qualified service
personnel.
•
People with physical or cognitive disabilities should use the device with supervision.
•
People with cardiac pacemakers, defibrillators or any other electrical implants should maintain a minimum
distance of 30 cm, as the device generates magnetic fields.
•
Do not use the device nearby mobile phones and devices that generate strong electromagnetic fields.
•
This device is not a toy. To prevent accidents and suffocation keep the device, the accessories and the
packing materials away from children and pets.
•
Protect the device against dirt. Never use aggressive cleansing agents or benzine to clean the device. We
recommend a soft, slightly damp microfiber cloth to clean the outer parts of the device. Before cleaning
make sure to switch off the device and take off from power supply!
•
Store the device in a dust-free, dry and cool place.
•
If the device is defective or without any further use, dispose of the device according to the Waste Electrical
and Electronic Equipment Directive WEEE. For further information, please contact your local authorities.
02 | PRODUCT DESCRIPTION
The
DÖRR Repro Stand Kit H75
is ideal for photographing documents, photos and objects. The stand is easy
to use and the height can be adjusted stepless by hand wheel. The illumination can be positioned in any
direction. Bulbs optional.
03 | NOMENCLATURE
1.
Base plate
2.
Column
2a) Thread for knurled screw (on the back of the camera bracket)
2b) Rotary wheel for height adjustment
2c) Quick release plate
2d) Locking lever quick release plate
2e) Safety pin
2f) Thread for hexagon bolt
3.
Lampshade
3a) Round socket for horizontal mounting rod
3b) Locking screw
3c) Power cord with On/Off switch
4.
Lamp holder
4a) Base plate locking screw
4b) Locking screw vertical mounting rod
5.
Vertical mounting rod (square profile)
5a) Mounting thread
6.
Horizontal mounting rod (round profile)
6a) Square socket for vertical mounting rod
6b) locking screw
7.
Hexagon bolt
8.
Washer
9.
Knurled screw
04 | ASSEMBLY AND USAGE
1.
Take the base plate (1) and the column (2). Insert the hexagon bolt (7) from below through the washer (8),
then through the pre-drilled hole at the base plate and then screw into the thread (2f) at the bottom of the
column. Tighten the hexagon bolt with the supplied wrench.
2.
Install the lamp holders (4) on the back of the base plate and fix them with the locking screw (4a).
3.
Unscrew the locking screw (4b) completely. Pull the locking screw through the threaded hole (5a) of the
square shaped mounting rod (5). Tighten the locking screw (4b) again. By Change the tilt angle by loosen/
tighten the locking screw (4b).
4.
Slide the square shaped mounting rods (5) through the square socket (6a) on the round mounting rods (6)
and fix them with the locking screws (6b).
5.
Slide the round shaped mounting rods (6) through the round socket (3a) on the lampshades (3) and fix them
with the locking screws (3b). The lampshades can be adjusted by loosen/tighten the locking screws (3b).
Screw in the bulbs (optional).
6.
Loosen the locking lever (2d) of the quick release plate by pushing the lever up. Remove the quick release
plate (2c) and attach it to the tripod socket of your camera. Snap the quick release plate with your camera
back into the holder until it clicks into place and the locking lever springs back to its original position. Press
the safety pin (2e) down to secure the quick release plate.
7.
Use the rotary wheel (2b) to set the desired distance between the camera and the object that you want to
photograph. To fix the height, turn the knurled screw (9) into the thread for the knurled screw (on the back
of the camera bracket) and tighten it slightly.
8.
Switch the lamps (lamps optional) on or off at the respective On/Off switch (3c). The repro stand is ready
to shoot.
05 | TECHNICAL SPECIFICATIONS
Bulb socket:
E27
Dimensions base plate:
48 x 40 cm
Height column:
82 cm
Camera distance to base plate:
min. 22 cm / max. 75 cm
Weight:
5,5 kg
06 | SCOPE OF DELIVERY
1x Base plate
1x Column
2x Lampshade with bracket
2x Square shaped rod
2x Round shaped rod
2x Lamp holder
07 | DISPOSAL, CE MARKING
WEEE INFORMATION
The Waste Electrical and Electronic Equipment Directive (WEEE Directive) is the European community direc-
tive on waste electrical and electronic equipment, which became European law in February 2003. The main
purpose of this directive is to prevent electronic waste. Recycling and other forms of waste recovery should be
encouraged to reduce waste. The symbol (trash can) on the product and on the packing means that used elec-
trical and electronic products should not be disposed of with general household waste. It is your responsibility
to dispose of all your electronic or electrical waste at designated collection points. Disposing of this product
correctly will help to save valuable resources and it is a significant contribution to protect our environment as
well as human health. For more information about the correct disposal of electrical and electronic equipment,
recycling and collection points please contact your local authorities, waste management companies, your
retailer or the manufacturer of this device.
ROHS CONFORMITY
This product is compliant with the European RoHS directive for the restriction of use of certain hazardous
substances in electrical and electronic equipment and its amendments.
CE MARKING
The CE marking complies with the European standards and indicates that the product meets the requirements
of the applicable EU directives.
doerr-foto.de
1x Hexagon bolt
1x Washer
1x Knurled screw
1x Wrench
DÖRR GmbH
Messerschmittstr. 1 · D-89231 Neu-Ulm · Fon +49 731.970 37 69 · [email protected] · doerr-foto.de
DÖRR Reprostand Set H75 (ohne Leuchtmittel)
Artikel Nr
361420
