background image

851-679 Rev. C

7

Dorner Mfg. Corp.

7350 Series Side Mount 90° Drive Package

Installation

US Version Side Drive Package

Required Tools

• 5/16

wrench

• 4 mm wrench

• 13 mm wrench

• 14 mm wrench

• Large flat head screwdriver

• Torque wrench

 Figure 2

 Figure 2           

Typical Side Drive Package Components 

(Figure 3)

.

 Figure 3

 Figure 3           

1.

On each side of conveyor, remove upper front head plate 
mounting screw and install spacer 

(Figure 4, item 1)

 

with longer screw 

(Figure 4, item 2)

.

 Figure 4

 Figure 4           

A

 WARNING

SEVERE HAZARD!

LOCK OUT POWER before removing guards 
or performing maintenance. Exposed moving 
parts can cause serious injury.

A

 WARNING

PUNCTURE HAZARD!

Handle drive shaft keyway with care. It may 
be sharp and could puncture the skin, 
causing serious injury.

NOTE

Gearmotor may be operated in positions 1 or 

(Figure 2)

.

1

3

1

Cover

2

Hex Head Cap Screw 5/16-18 x .75" (x2)

3

Hex Head Cap Screw 5/16-18 x .50" (x2)

4

Cover Bracket

5

Support Arm

6

Mounting Bracket

7

Hex Head Cap Screw M8-1.25 x 40 mm

8

Gearmotor Assembly

2

6

1

3

8

4

7

5

1

2

Summary of Contents for 73U005HS423FN





















Reviews: