Dorner 70-40 Safety, Setup, Operation & Maintenance Manual Download Page 2

70–40 and 70–41 Emergency Stop Kit Setup, Operation & Maintenance Manual

851-462 Rev. B

2

Dorner Mfg. Corp.

The safety alert symbol, black triangle with white
exclamation, is used to alert you to potential
personal injury hazards.

Ç

Ç

Ç

Climbing, sitting, walking or
riding on conveyor will
cause severe injury.

KEEP OFF CONVEYORS.

DANGER

Ç

DANGER

DO NOT OPERATE
CONVEYORS IN AN
EXPLOSIVE ENVIRONMENT.

Controller must be properly grounded. Failure to
properly ground controller may cause injury to
personnel.

Ç

Ç

Ç

Hazardous voltage will
cause severe injury or
death.

LOCKOUT POWER BEFORE
wiring.

DANGER

Ç

Exposed moving parts can
cause severe injury.

DO NOT ATTEMPT
ADJUSTMENTS WITH
CONVEYOR RUNNING.

Ç

Dorner cannot control the
physical installation and
application of conveyors.
Taking protective measures
is the responsibility of the
user.

When conveyors are used in
conjunction with other
equipment or as part of a
multiple conveyor system,
CHECK FOR POTENTIAL
PINCH POINTS and other
mechanical hazards before
system start-up.

Introduction

IMPORTANT:

 Some illustrations may show

guards removed. Do NOT operate equipment with-
out guards.

Upon receipt of shipment:

D

Compare shipment with packing slip. Contact factory
regarding discrepancies.

D

Inspect packages for shipping damage. Contact carrier
regarding damage.

D

Accessories may be shipped loose. See accessory in-
structions for installation.

Dorner conveyors are covered by the following patent
numbers: 5131529, 5156260, 5156261, 5174435,
5203447, 5265714, 5875883, and corresponding pat-
ents and patent applications in other countries.

Dorner’s Limited Warranty applies.

Dorner reserves the right to make changes at any time
without notice or obligation.

Warnings – General Safety

Summary of Contents for 70-40









Reviews: