manualshive.com logo in svg

Dormakaba Saffire LX, Installation Manual

Share
Download
Dormakaba Saffire LX Installation Manual Download Page 3

Page 3 of 28 

Saffire LX 

1. Introduction and disclaimers

Caution: 

Please read and follow all directions carefully. Wear safety glasses when 

making the holes.  

Target  Audience: 

These  instructions  are  designed  for  use  by  maintenance 

professionals  or  lock  installers  who  are  familiar  with  common  safety  practices  and 
competent to perform the steps described. dormakaba is not responsible for damage 
or malfunction due to incorrect installation however arising.

  

Important: 

Carefully inspect windows, doorframe, door, etc. to ensure that the 

recommended procedures will not cause damage. dormakaba Lodging Systems 
standard warranty does not cover damages caused by installation.  

Respect applicable building codes regarding handle height.

 

Definition of Terms: 

In these instructions, the term ASM refers to American 

Standard Mortise and ADB refers to Autodeadbolt Mortise. 

Technical Assistance

 

For technical assistance, call:  

1.877.468.3555 / +1.514.340.9025RT: 1.800.999.6213 / +1.248.837.3700 

2. Recommended Tools

Summary of Contents for Saffire LX





























Reviews:

No comments

Brands by name

Popular brands

Load more brands