background image

16

15

1

2

Securing Your Child in the Child
Restraint

Place the child’s bottom
and back flat against the
child restraint. This will
increase comfort and
allow the harness system
to be properly tightened.
Pull harness straps over
child’s shoulders.

Push each buckle plate
into buckle until you hear
a “click”. Pull up on
harness straps and down
on the crotch strap to
make sure buckle is
locked.

5

Rethread harness straps
into new harness slot
location.

Note:

D

DO

O  N

NO

OT

T twist

harness straps.

WARNING

Failure to reinstall the harness straps
correctly could result in serious injury or
death.

Do not mistake comfort for safety. Harness
straps must be snugly adjusted.

!

6

From the back of the child
restraint, refasten harness
straps to splitter plate.

Note:

D

DO

O  N

NO

OT

T twist

harness straps.

continued on next page.

7

Determine which of the
three buckle slots that is
both comfortable and snug
to use. (See “Adjusting the
Buckle” section)

Note:

Thread buckle and

buckle strap through slot
closest to child

Note:

The style of buckle may vary, but the operation of

the buckle is the same.

3

Snap the chest clip
together.

4358-3951B Can Scenera Eng  6/20/07  8:48 AM  Page 21

Summary of Contents for Scenera



























Reviews: