DORCHESTER DR-SE 18 Installation, Commissioning And Maintenance Instructions Download Page 3

 

HAMWORTHY HEATING LTD 

 

                          

Page

 

DORCHESTER DR-SE 

 

500001062/D 

 
NOTE:

 

THESE INSTRUCTIONS MUST BE READ AND UNDERSTOOD BEFORE 

INSTALLING, COMMISSIONING, OPERATING OR SERVICING EQUIPMENT. 
 
 

THIS HEATER IS FOR USE ON 2nd AND 3rd FAMILY GASES ONLY. RELEVANT DETAILS 
MUST BE FOUND WITHIN THIS DOCUMENT AND CHECKED AGAINST THE GAS TO BE 
FIRED AND FOR WHICH GAS THE HEATER IS ADJUSTED, PRIOR TO FIRST FIRING. 
 
THIS HEATER IS INTENDED TO BE INSTALLED IN A ROOM SEPARATED FROM LIVING 
ROOMS AND PROVIDED WITH APPRORIATE VENTILATION DIRECTLY TO THE OUTSIDE. 
 
IF IT IS TO BE INSTALLED IN A LIVING ROOM, THE HEATER MUST BE FITTED WITH AN 
ADDITIONAL COMBUSTION PRODUCTS DISCHARGE SAFETY DEVICE TOGETHER WITH 
THE APPROPRIATE VENTILATION. 

 
THIS HEATER HAS BEEN TESTED FOR COMPLIANCE TO EUROPEAN DIRECTIVES 
90/396/EEC AND 89/336/EEC AMENDED BY 92/31/EEC AND 93/68/EEC CERTIFICATE 
NUMBER 0085 AQ. 

 
 
 

 
PUBLICATION NO. 500001062 
ISSUE  ‘D’ 
February 2005

 

DORCHESTER 

DR-SE 18 & DR-SE 20 P/P 

HOT WATER 

STORAGE HEATERS 

 

 

Installation, Commissioning 

and Maintenance Instructions 

 

(Minisit 710 gas control valve) 

Heaters with serial numbers from 80000000 

Summary of Contents for DR-SE 18





























Reviews: