background image

11

EN

Self-Contained Air Conditioning System 

Disposal

All conditioning units have a terminal strip, labeled 
for proper connections, inside the electric box. The 
wiring diagram inside the electric box supersedes ABYC 
standards. Use the correct size circuit breaker to protect 
the system as specified by the air conditioning units data 
plate label. A minimum of 12 AWG boat cable should 
be used to supply power to the air conditioning unit and 
the seawater pump. Make all connections using ring or 
captive fork terminals.

Observe the following when making electrical 
connections:

•  Alternating current (AC) grounding must be 

connected to the ground terminal (GRND) at the AC 
power input terminal block.

•  Connections between the vessel’s AC system 

grounding conductor and the vessel’s direct current 
(DC) negative or bonding system should be made 
as part of the vessel’s wiring. When servicing or 
replacing existing equipment that contains a chassis-
mounted ground stud, check the vessel’s wiring for 
these connections.

The air conditioning unit must be connected to the 
boat’s bonding system to prevent corrosion due to stray 
electrical current. Ensure that the AC ground of the 
air conditioning unit is properly connected to the AC 
ground of the boat. Within the boat itself, ensure that 
the AC ground bus is connected to the DC ground bus 
at exactly one place. All pumps, metallic valves, and 
fittings in the seawater circuit that are isolated from the 
air conditioning unit by PVC or rubber hoses, must be 
individually bonded to the boat’s bonding system.

7  Disposal

 

M

Place the packaging material in the appropriate 
recycling waste bins, whenever possible. Consult 
a local recycling center or specialist dealer for 
details about how to dispose of the product in 
accordance with all applicable national and local 
regulations.

8  Warranty Information

Refer to the sections below for information about 
warranty and warranty support in the US, Canada, and all 
other regions.

8 .1  United States and Canada

LIMITED WARRANTY AVAILABLE AT WWW.DOMETIC.
COM/WARRANTY.

IF YOU HAVE QUESTIONS, OR TO OBTAIN A COPY 
OF THE LIMITED WARRANTY FREE OF CHARGE, 
CONTACT:

DOMETIC CORPORATION 
MARINE CUSTOMER SUPPORT CENTER 
2000 NORTH ANDREWS AVENUE 
POMPANO BEACH, FLORIDA, USA 33069 
1-800-542-2477

8 .2 All Other Regions

The statutory warranty period applies. If the product is 
defective, please contact the manufacturer’s branch in 
your region (see the back of the instruction manual for 
the addresses) or your retailer.

For repair and guarantee processing, please include the 
following documents when you send in the device:

•  A copy of the receipt with purchasing date 

•  A reason for the claim or description of the fault

Summary of Contents for DCG













Reviews: