Dometic CONCERTO 3210 Installation And Operation Instructions Manual Download Page 5

5

STEP 9: 

WITH THE ELECTRICAL POWER OFF,

 route

#14 gauge stranded copper wire from 12 VDC ground and
positive 12 VDC from the fuse panel through a 2-amp 

fuse

or circuit

 breaker. Leave at least 12 inches (305 mm) of 

wire for 

connecting to toilet (fig. 9).

STEP 10: Connect the holding tank to the bottom of the
discharge flange.
STEP 11: Slide the four T-bolts into the slots of the floor
flange. Install the flange gasket over the T-bolts (fig. 10).

Fig. 9

Fig. 10

STEP 12: Install floor flange adapter with words “THIS SIDE
UP” facing up. Tighten adapter to floor flange using four flat
washers and hex nuts. Tighten in criss-cross pattern
(fig. 11).

STEP 13: Temporarily set the toilet in place on the floor
flange (fig. 14).

STEP 14: Mark the holes for the two toilet mounting bolts
(fig. 15).

Fig. 16

STEP 15: Pick up toilet and set aside. Drill 3/16-inch
pilot holes in the floor (fig. 16).

Fig. 15

Fig. 14

STEP 16: With toilet close to floor flange, connect flex-
ible water supply hose to the water line fitting (fig. 17).

Fig. 11

Fig. 17

IMPORTANT: If replacing an existing toilet with 2-bolt
floor flange, drill two 5/16-inch dia. holes in old floor
flange that align with two additional holes in floor
flange adapter. Use two #10 or 12 x 1-1/2-inch wood
screws and washers for these drilled holes, and two
T-bolts with flat washers and nuts to fasten flange
gasket and floor flange adapter to old floor flange.
Do not use old hardware or seal.

Summary of Contents for CONCERTO 3210













Reviews: