background image

12

Warranty / Customer Service 

Dometic 4410N Commode

Manufacturer’s One-Year Limited Warranty

Dometic Corporation warrants, to the original purchaser only, that this toilet is free from 
defects in material and workmanship for a period of one (1) year from the date of  
installation .
Dometic reserves the right to replace or repair any part of this product that proves, 
upon inspection by Dometic, to be defective in material or workmanship .  All labor and 
transportation costs or charges incidental to warranty service are to be borne by the 
purchaser-user .

EXCLUSIONS

IN NO EVENT SHALL DOMETIC BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL 
DAMAGES, FOR DAMAGES RESULTING FROM IMPROPER INSTALLATION, OR FOR 
DAMAGES CAUSED BY NEGLECT, ABUSE, ALTERATION, OR USE OF UNAUTHOR-
IZED COMPONENTS . ALL IMPLIED WARRANTIES, INCLUDING ANY IMPLIED  
WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE, 
ARE LIMITED TO A PERIOD OF ONE (1) YEAR FROM DATE OF INSTALLATION .

IMPLIED WARRANTIES

No person is authorized to change, add to, or create any warranty or obligation other 
than that set forth herein .
Implied warranties, including those of merchantability and fitness for a particular  
purpose, are limited to one (1) year from the date of installation .
To obtain warranty service, contact Dometic Corp ., Sanitation Div . at 1-800-321-9886 .

Questions about technical details, operation, replacement parts, or servicing 
may be directed to:

Dometic Corporation 
Sanitation Division 
13128 State Route 226 
Big Prairie, OH 44611
Phone: 330-439-5550 
Toll free: 

1-800-321-9886

Customer service

Customer Service hours:  
0800-1630 ET  USA

Dometic Corporation, Sanitation Division 

 

13128 State Rt. 226, P.O. Box 38 

Big Prairie, OH 44611 USA  

 1-800-321-9886 • Fax: 330-496-3097 

www.Dometic.com

 

REVISION A

 

Form No. 600346973  8/17 

©2017 Dometic Corporation

Summary of Contents for 4410N













Reviews: