Dolmar ES-2130 A Instruction Manual Download Page 4

4

1

2

3

4

5

SAFETY PRECAUTIONS

General precautions

To ensure correct operation the user has to read this instruc-
tion manual 

to make himself familiar with the characteristics 

of the electric chain saw. Users insuf

Þ

 ciently informed will risk 

danger to themselves as well as others due to improper han-
dling. 

It is recommended only to lend the electric chain saw to people 
who have proven to be experienced with electric chain saws. 
Always hand over the instruction manual.

First users should ask the dealer for basic instructions to become 
familiarized with the characteristics of engine powered sawing.

-  Familiarize yourself with the use of an electric chain saw by 

cutting off lengths from a log on a sawhorse. 

 

-   Children and young persons aged under 18 years must not be 

allowed to operate the electric chain saw. Persons over the age 
of 16 years may, however, use the chain saw for the purpose 
of being trained while under supervision of a quali

Þ

 ed trainer.

Use electric chain saws always with the utmost care and atten-
tion.

-  Operate the electric chain saw only if you are in good physical 

condition. Perform all work calm and carefully. The user has to 
accept liability for others.

Never use the electric chain saw after the consumption of alcohol 
or drugs or medication. 

Personal protective equipment

In order to avoid head, eye, hand or foot injuries as well as 
to protect your hearing the following protective equipment 
must be used during operation of the electric chain saw.

The kind of clothing should be appropriate, i. e. it should be tight-

Þ

 tting but not be a hindrance. Do not wear jewellery or clothing 

which could become entangled with bushes or shrubs.

- The 

protective helmet 

(1) is to be checked in regular intervals 

for damage and is to be replaced after 5 years at the latest. Use 
only approved protective helmets.If you have long hair wear a 
hairnet.

- The 

face shield

 (2) of the protective helmet (or the goggles) 

protect against sawdust and wood chips. During operation of 
the electric chain saw always wear a goggle or a face shield to 
prevent eye injuries.

- Wear 

adequate

 noise protection equipment

 (ear muffs (3), 

ear plugs, etc.). Octave brand analysis upon request. 

- The 

protective brace and bib overall

 (4) is made of a nylon 

structure with 22 layers and protects against cuts. We strongly 
recommend its use. In any case wear a long pair of trousers made 
of solid material during operation of the electric chain saw. 

Protective gloves

 (5) made of thick leather are part of the pre-

scribed equipment and must always be worn during operation 
of the electric chain saw.

During operation of the electric chain saw 

safety shoes

 or boots  

(6) 

Þ

 tted with anti skid sole, steel toe caps and protection for 

the leg are always to be used. Safety shoes equipped with a 
protective layer provide protection against cuts and ensure a 
secure footing.

Putting into operation

-  Do not operate the electric chain saw when it rains or in wet or 

moist environment because the motor is not waterproof.

-  If the electric chain saw is moist, it must not be put into opera-

tion.

-  Avoid physical contact with grounded surfaces.

Do not operate the electric chain saw next to in

ß

 ammable gases 

or dusts. 

Explosion hazard.

-  Do always lead the power supply cable behind the user. Take 

care that the cable is not clamped or cut by sharp-edged objects. 
Lay the cable such that nobody is endangered.

-  Insert the plug only into safety sockets with approved installa-

tion. Make sure that the mains voltage corresponds to that on 
the identi

Þ

 cation plate. Back-up fuse 16 A. If the saw is going to 

be used outdoors connect it to a fault-current (FI) circuit breaker 
with max. 30 mA triggering current.

Summary of Contents for ES-2130 A

























Reviews: