Dolby Laboratories DSR1260 Owner'S Manual Download Page 4

1

 

Important safety and regulatory information

Safety

INSTALLER ASSUMES ALL RESPONSIBILITY AND LIABILITY FOR THE INSTALLATION OF THIS PRODUCT.
No information contained in this guide is intended as a warranty on the part of Dolby. Anyone using

this information assumes all liability arising from its use. Product abuse, use of the product not in

accordance with Dolby instructions, or use in an application for which the product has not been

designed is not covered under any Dolby warranty, nor is Dolby liable for any loss or damage.
Installation must be performed by qualified, licensed, and insured installers, and installed in

accordance with all laws, rules, and regulations applicable to the installation site. Failure to do so

could result in serious personal injury or even death. Prior to installing this product, read and

completely understand the installation instructions. You must read these instructions to prevent

personal injury and property damage. Keep the installation instructions in an easily accessible location

for future reference.
A licensed professional engineer must approve the placement and method of attachment to the

building structure prior to the installation of the system.
All information presented herein is based upon materials and practices common to North America and

may not directly apply to other countries because of differing material dimensions, specifications,

and/or local regulations. Installers in other countries should consult with appropriate engineering and

regulatory authorities for specific guidelines.
Any supplied rigging hardware is intended only for use with the specified loudspeaker(s). The installer

assumes all risk of loss and/or injury arising out of the use of the supplied rigging hardware with any

other loudspeaker. All other rigging is considered part of the venue and/or installer-supplied

equipment and is not addressed in this guide. This guide is not a comprehensive source for rigging in

general. Installer assumes all responsibility for ensuring that accepted rigging and safety practices are

employed. Installer assumes all responsibility for the appropriate use of Dolby supplied rigging

hardware and follows at a minimum all applicable laws, rules, and regulations in force for each venue.
Make sure that no water pipes, natural gas lines, electrical wire, or conduit are present where the

speaker is to be installed. Cutting or drilling into water pipes, natural gas lines, electrical wire, or

conduit could cause serious personal injury or property damage.
Dolby is not responsible for the application of its products for any purpose or the misuse of this

information for any purpose. Furthermore, Dolby is not responsible for the abuse of its products

caused by avoiding compliance with inspection and maintenance procedures or any other abuse.
Proper selection of mounting hardware is not included; proper assembly and installation of mounting

hardware, including, but not limited to, selection of appropriate weight-bearing support and bracket

use, are the exclusive responsibility of the installer. Dolby disclaims any liability, including damage or

injury, for the use of mounting hardware supplied by any party other than Dolby. Any modification to

Important safety and regulatory information

Dolby DSR1260/DSR1280 Owner's Manual

4

8800294 Issue 1

1 January 2022

Summary of Contents for DSR1260








































Reviews: