Dodge 2016 Viper SRT ACR Owner'S Manual Download Page 49 | Manualshive

Page: 49 / 427

background image

WARNING!

(Continued)

only used to install rear-facing or forward-facing
child restraints that have a harness for restraining
the child.

Supplemental Restraint System (SRS)

Air Bag System Components

Your vehicle may be equipped with the following air bag
system components:

•

Occupant Restraint Controller (ORC)

•

Air Bag Warning Light

•

Steering Wheel and Column

•

Instrument Panel

•

Knee Impact Bolsters

•

Advanced Front Air Bags

•

Supplemental Side Air Bags

•

Front and Side Impact Sensors

•

Seat Belt Pretensioners

•

Seat Belt Buckle Switch

•

Seat Track Position Sensors

•

Occupant Classification System

Advanced Front Air Bags

This vehicle has Advanced Front Air Bags for both the
driver and front passenger as a supplement to the seat
belt restraint systems. The driver’s Advanced Front Air
Bag is mounted in the center of the steering wheel. The
passenger’s Advanced Front Air Bag is mounted in the
instrument panel, above the glove compartment. The
words “SRS AIRBAG” or “AIRBAG” are embossed on
the air bag covers.

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

47

«
...
47
48
49
50
51
...
»

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2016 Viper SRT ACR

Brand: AAMP of America Pages: 6

Electronic Parking Disc II

Brand: Jacob Jensen Pages: 28

Brand: GMC Pages: 20

Brand: Kia Pages: 10

Brand: Doug Thorley Headers Pages: 5

Brand: Edelbrock Pages: 2

Brand: Saab Pages: 445

SmartShot Automatic 12V 1.5 Amp 5 Stage

Brand: Yuasa Pages: 44

Chevrolet Silverado 2500HD 2021

Brand: GMC Pages: 433

Brand: Simplicity Pages: 10

Brand: Mobility Networks Pages: 52

2013 GMC Savana

Brand: GMC Pages: 398

Brand: Rugged Ridge Pages: 3

Brand: Ford Pages: 10

Brand: Fiat Pages: 204

Nemesis Ultra FNU200

Brand: Purpleline Pages: 4

650i Convertible

Brand: BMW Pages: 256

Brand: Chevrolet Pages: 516

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands