Dodge 2016 Viper SRT ACR Owner'S Manual Download Page 381 | Manualshive

Page: 381 / 427

background image

CAUTION!

(Continued)

result in a dangerous electrical system overload. If
a properly rated fuse continues to blow, it indicates
a problem in the circuit that must be corrected.

VEHICLE STORAGE

We recommend that you follow these guidelines for
storing your vehicle for extended periods.

•

Fill the fuel tank. This will prevent water condensation
inside the tank. If you plan to store your vehicle more
than two months, add an anti-oxidant fuel stabilizer to
the fuel tank.

•

Change the oil to remove any corrosive combustion
related acids in the crankcase.

•

Check that the radiator coolant level of protection is to
at least -20°F (-29°C).

•

Make sure that all tires are inflated to the optimum
pressure.

•

Wash and wax the vehicle to protect the finish.

•

Store the vehicle in a dry, well-ventilated location.

•

Move the wiper blades away from the windshield.

•

Block the wheels. Do not apply the parking brake.

•

Cut blocks of plywood about the same size of the tires.
Cover each block with indoor/outdoor carpeting and
place them between the tires and concrete. This will
prevent tire flat spotting.

•

For long-term storage, remove the tires and put the
vehicle up on blocks. Stack the tires on plywood and
cover with a tarp to prevent flat spotting.

7

MAINTAINING YOUR VEHICLE

379

«
...
379
380
381
382
383
...
»

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2016 Viper SRT ACR

Brand: Saab Pages: 75

Brand: Jeep Pages: 603

Brand: Jeep Pages: 80

NPL-TV 7874 DIGITAL

Brand: Napoli Pages: 20

Brand: BGS technic Pages: 5

Brand: Oldsmobile Pages: 344

Brand: ABL Pages: 66

Brand: Prorack Pages: 14

BLADE-AL(TB)-TL2

Brand: iDataLink Pages: 9

Brand: Magneti Marelli Pages: 2

Intercooler Kit Type 31

Brand: GReddy Pages: 9

v.LOGiC Intelligent Solution V5-NTG46

Brand: Caraudio-Systems Pages: 18

Brand: BMW Pages: 38

Brand: Parkeon Pages: 43

Brand: Volvo Pages: 266

Brand: Westin Pages: 3

Brand: Prorack Pages: 15

Brand: Blaupunkt Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands