Dodge 2016 Viper SRT ACR Owner'S Manual Download Page 364 | Manualshive

Page: 364 / 427

background image

WARNING!

(Continued)

•

Do not allow petroleum based fluid to contaminate
the brake fluid. Brake seal components could be
damaged, causing partial or complete brake failure.
This could result in an accident.

Change Brake Fluid

Brake fluid will tend to absorb moisture from the atmo-
sphere over time. If the fluid becomes contaminated with
water, brake performance will deteriorate. Therefore, the
brake fluid must be changed at the intervals specified in
the “Maintenance Schedule.” Refer to “Maintenance
Schedule” for further information. See your authorized
dealer for service.

Manual Transmission

Transmission Fluid Level Check

Check the fluid in the transmission when performing
other underbody services.

Check the fluid level by removing the fill plug located on
the left side of the transmission. The fluid level should be
approximately 1/4 in (6.4 mm) below the bottom of the
fill hole. Add fluid, if necessary, to maintain the proper
level. Refer to “Fluids, Lubricants, And Genuine Parts” in
“Maintaining Your Vehicle” for further information.

NOTE: DO NOT

overfill transmission, damage can

occur.

362

MAINTAINING YOUR VEHICLE

«
...
362
363
364
365
366
...
»

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2016 Viper SRT ACR

Brand: Ignition Pages: 1

Brand: Uebler Pages: 18

Brand: FABBRI PORTATUTTO Pages: 2

Brand: Yakima Pages: 21

Brand: Gator Pages: 8

Brand: Mazda Pages: 13

Escalade ESV 2014

Brand: Cadillac Pages: 508

Brand: Hama Pages: 2

Brand: Kuda Pages: 3

Brand: BURY Pages: 2

Brand: SCC Pages: 4

Brand: BrandMotion Pages: 6

Brand: Oldsmobile Pages: 380

Easy Air Auto Screen

Brand: Wagan Pages: 8

Brand: TATA Motors Pages: 151

QUICKDRAW RACHET TIE-DOWNS 855

Brand: Thule Pages: 3

Brand: MBRP Pages: 5

Brand: Smappee Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands