Dodge 2016 Viper SRT ACR Owner'S Manual Download Page 357 | Manualshive

Page: 357 / 427

background image

Cooling System — Drain, Flush And Refill

NOTE:

Some vehicles require special tools to add coolant

properly. Failure to fill these systems properly could lead
to severe internal engine damage. If any coolant is
needed to be added to the system please contact your
local authorized dealer.

If the engine coolant (antifreeze) is dirty or contains
visible sediment, have an authorized dealer clean and
flush with OAT coolant (antifreeze) (conforming to
MS.90032).

Refer to the “Maintenance Schedule” for the proper
maintenance intervals.

Selection Of Coolant

Refer to “Fluids, Lubricants, And Genuine Parts” in
“Maintaining Your Vehicle” for further information.

CAUTION!

•

Mixing of engine coolant (antifreeze) other than
specified Organic Additive Technology (OAT) en-
gine coolant (antifreeze), may result in engine
damage and may decrease corrosion protection.
Organic Additive Technology (OAT) engine cool-
ant is different and should not be mixed with
Hybrid Organic Additive Technology (HOAT) en-
gine coolant (antifreeze) or any “globally compat-
ible” coolant (antifreeze). If a non-OAT engine
coolant (antifreeze) is introduced into the cooling
system in an emergency, the cooling system will
need to be drained, flushed, and refilled with fresh
OAT coolant (conforming to MS.90032), by an au-
thorized dealer as soon as possible.

•

Do not use water alone or alcohol-based engine
coolant (antifreeze) products. Do not use additional

(Continued)

7

MAINTAINING YOUR VEHICLE

355

«
...
355
356
357
358
359
...
»

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2016 Viper SRT ACR

Brand: cam Pages: 2

Brand: Dapper Lighting Pages: 2

Brand: Alpine Pages: 2

Brand: Whispbar Pages: 15

Brand: Mercedes-Benz Pages: 30

Brand: Maserati Pages: 210

Brand: OnStar Pages: 22

Brand: Thule Pages: 8

Brand: ULTIMATE SPEED Pages: 34

Brand: Gator Pages: 6

Brand: F.lli Menabo Pages: 16

Brand: Cadillac Pages: 19

Brand: Scosche Pages: 12

1999 Crown Victoria

Brand: Ford Pages: 208

Brand: STO N SHO Pages: 7

Brand: FAAFTECH Pages: 2

Brand: Honda Pages: 280

Brand: Cadillac Pages: 362

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands