Dodge 2016 Viper SRT ACR Owner'S Manual Download Page 157 | Manualshive

Page: 157 / 427

background image

Red Warning

Light

What It Means

If the light turns on while driving, safely pull over and stop the vehicle. If the A/C system is
on, turn it off. Also, shift the transmission into NEUTRAL and idle the vehicle. If the tempera-
ture reading does not return to normal, turn the engine off immediately and call for service.
Refer to “If Your Engine Overheats” in “What To Do In Emergencies” for further information.

Charging System Warning Light

Red Telltale

Light

What It Means

Charging System Warning Light

This light shows the status of the electrical charging system. If the light stays on or comes
on while driving, turn off some of the vehicle’s nonessential electrical devices or increase
engine speed (if at idle). If the charging system light remains on, it means that the vehicle is
experiencing a problem with the charging system. Obtain SERVICE IMMEDIATELY. See an
authorized dealer.
If jump starting is required, refer to “Jump Starting Procedures” in “What To Do In Emergencies.”

4

UNDERSTANDING YOUR INSTRUMENT PANEL

155

«
...
155
156
157
158
159
...
»

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2016 Viper SRT ACR

Brand: Taffio Pages: 8

Brand: Phonocar Pages: 6

Brand: Mazda Pages: 122

Brand: Easee Pages: 12

Brand: Cadillac Pages: 529

Brand: Toro Pages: 16

Brand: Honda Pages: 24

Stargazer Spirit XTR Skylight

Brand: Lippert Pages: 8

Brand: Mobridge Pages: 20

Brand: Mobileye Pages: 29

Brand: Saab Pages: 37

Brand: TATA Motors Pages: 308

Brand: Green Valley Pages: 17

Brand: Setma Pages: 13

$T-Rex TEX-51127 Installation Manual preview$

Brand: T-Rex Pages: 9

Brand: Renault Pages: 246

Brand: Metra Electronics Pages: 2

Escalade EXT 2013

Brand: Cadillac Pages: 476

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands