Dodge 2016 Viper SRT ACR Owner'S Manual Download Page 122 | Manualshive

Page: 122 / 427

background image

NOTE:

In order to ensure proper operation, the Elec-

tronic Speed Control System has been designed to shut
down if multiple speed control buttons are pushed at the
same time. If this occurs, the Electronic Speed Control
System can be reactivated by pushing the Electronic
Speed Control ON/OFF button and resetting the desired
vehicle set speed.

To Activate

Push the ON/OFF button to activate the Electronic Speed
Control. The Cruise Indicator Light in the Driver Infor-
mation Display (DID) will illuminate. To turn the system
off, push the ON/OFF button a second time. The Cruise
Indicator Light will turn off. The system should be
turned off when not in use.

WARNING!

Leaving the Electronic Speed Control system on
when not in use is dangerous. You could accidentally
set the system or cause it to go faster than you want.
You could lose control and have an accident. Always
leave the system OFF when you are not using it.

To Set A Desired Speed

Turn the Electronic Speed Control ON. When the vehicle
has reached the desired speed, push the SET (-) button
and release. Release the accelerator and the vehicle will
operate at the selected speed.

NOTE:

The vehicle should be traveling at a steady speed

and on level ground before pushing the SET (-) button.

120

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
120
121
122
123
124
...
»

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2016 Viper SRT ACR

Brand: iDataLink Pages: 106

Brand: Porsche Pages: 144

Brand: Carcomm Pages: 2

Brand: Whispbar Pages: 14

Green Motion DC 66

Brand: Eaton Pages: 18

Brand: Ranger design Pages: 24

Brand: AutoLoc Pages: 6

Brand: GROM Audio Pages: 20

Brand: Renault Pages: 3699

Brand: Axxess Pages: 4

Aura Mobile BT MCP-2014

Brand: Spracht Pages: 2

Brand: Mercedes-Benz Pages: 66

WG Grand Cherokee 2002

Brand: Jeep Pages: 74

Brand: Opel Pages: 44

Brand: Setma Pages: 16

Brand: Menabo Pages: 4

Q7 V12 TDI QUATTRO -

Brand: Audi Pages: 20

M-RK 344A4616P1

Brand: Ericsson Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands