Dodge 2016 Viper SRT ACR Owner'S Manual Download Page 114 | Manualshive

Page: 114 / 427

background image

Interior Light Control

Rotate the dimmer control completely upward to the
second detent to turn on the interior lights. The interior
lights will remain on when the dimmer control is in this
position.

Interior Light Defeat (OFF)

Rotate the dimmer control to the extreme bottom OFF
position. The interior lights will remain off when the
doors are open.

Parade Mode (Daytime Brightness Feature)

Rotate the instrument panel dimmer control upward to
the first detent. This feature brightens all text displays
such as the odometer, Driver Information Display (DID),
and radio when the position lights or headlights are on.

WINDSHIELD WIPERS AND WASHERS

The multifunction lever operates the windshield wipers
and washer when the ignition is placed in the ON/RUN
or ACC position. The multifunction lever is located on
the left side of the steering column.

Interior Lights

112

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
112
113
114
115
116
...
»

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2016 Viper SRT ACR

Brand: Garmin Pages: 2

MagicWatch MWE250

Brand: Waeco Pages: 172

Impala Limited 2014

Brand: Chevrolet Pages: 356

Brand: Meta System Pages: 16

Brand: Yakima Pages: 13

Brand: Mobility Networks Pages: 52

Brand: Honda Pages: 569

Brand: TATA Motors Pages: 151

QUICKDRAW RACHET TIE-DOWNS 855

Brand: Thule Pages: 3

Prime Design VBI-FT31B

Brand: Safe Fleet Pages: 12

Brand: Thule Pages: 4

Brand: Car-Interface Pages: 23

Brand: Reliant Pages: 116

PRO-FLO XT 3527

Brand: Edelbrock Pages: 39

Brand: Kargo Master Pages: 9

Brand: HUSKY LINERS Pages: 4

Brand: iOttie Pages: 19

Brand: Lincoln Pages: 364

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands