Dodge 2012 Charger Owner'S Manual Download Page 231 | Manualshive

Page: 231 / 594

background image

To Resume Speed

Press the RES

+

button and release. Then remove your

foot from the accelerator pedal. The EVIC will display the
last set speed.

NOTE:

You can resume ACC from a minimum of

20 mph (32 km/h).

WARNING!

The Resume function should only be used if traffic
and road conditions permit. Resuming a set speed
that is too high or too low for prevailing traffic and
road conditions could cause the vehicle to accelerate
or decelerate too sharply for safe operation. Failure to
follow these warnings can result in a collision and
death or serious personal injury.

To Vary The Speed Setting

While ACC is set, you can increase the set speed by
pressing and holding the RES

+

button. If the button is

continually pressed, the set speed will continue to in-
crease in 5 mph (8 km/h) increments until the button is
released. The increase in set speed is reflected in the EVIC
display.

Pressing the RES

+

button once will result in a 1 mph

(1.6 km/h) increase in set speed. Each subsequent tap of
the button results in an increase of 1 mph (1.6 km/h).

While ACC is set, the set speed can be decreased by
pressing and holding the SET

-

button. If the button is

continually pressed, the set speed will continue to de-
crease in 5 mph (8 km/h) increments until the button is
released. The decrease in set speed is reflected in the
EVIC display.

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

229

«
...
229
230
231
232
233
...
»

Summary of Contents for 2012 Charger



















































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2012 Charger

2011 grand cherokee

Brand: Jeep Pages: 22

2013 Grand Cherokee

Brand: Jeep Pages: 704

Brand: Jeep Pages: 558

QuadraTop Adventure Top S

Brand: Quadratec Pages: 20

Brand: Mazda Pages: 527

2008 Escalade EXT

Brand: Cadillac Pages: 496

3-series convertible

Brand: BMW Pages: 98

Brand: Subaru Pages: 21

Brand: MASCOT Pages: 12

Brand: TBC Pages: 12

Brand: Prorack Pages: 14

Brand: TATA Motors Pages: 236

ADARAC Aluminum M Series

Brand: aci Pages: 16

Brand: Imiola HAK-POL Pages: 3

Brand: Meta System Pages: 22

ZapCharger Portable C1

Brand: ZAPTEC Pages: 20

84 61 0 028 926

Brand: BMW Pages: 13

Brand: Roadtrek Pages: 61

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands