manualshive.com logo in svg

Dodge 2011 Grand Caravan, Owner'S Manual

Looking for a user manual for your Dodge 2011 Grand Caravan? Look no further! Download the comprehensive manual for free from manualshive.com, providing you with all the essential information you need to operate and maintain your vehicle. Simply click the link and get instant access to the manual.

Share
Download
background image

CAUTION!

•

Failure to properly maintain your vehicle or per-
form repairs and service when necessary could
result in more costly repairs, damage to other
components or negatively impact vehicle perfor-
mance. Immediately have potential malfunctions
examined by an authorized Chrysler Group LLC
dealership or qualified repair center.

•

Your vehicle has been built with improved fluids
that protect the performance and durability of
your vehicle and also allow extended maintenance
intervals. Do not use chemical flushes in these
components as the chemicals can damage your
engine, transmission, power steering or air condi-
tioning. Such damage is not covered by the New
Vehicle Limited Warranty. If a flush is needed
because of component malfunction, use only the
specified fluid for the flushing procedure.

Engine Oil

Checking Oil Level

To assure proper engine lubrication, the engine oil must
be maintained at the correct level. Check the oil level at
regular intervals, such as every fuel stop. The best time to
check the engine oil level is about five minutes after a
fully warmed engine is shut OFF or before starting the
engine after it has sat overnight.

Checking the oil while the vehicle is on level ground will
improve the accuracy of the oil level readings. Maintain
the oil level between the MIN and MAX markings on the
dipstick. Adding one quart of oil when the reading is at
the MIN mark will result in a MAX reading on these
engines.

472

MAINTAINING YOUR VEHICLE

Summary of Contents for 2011 Grand Caravan



















































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Grand Caravan

ABL eMH1 WALLBOX Manual preview
eMH1 WALLBOX
Brand: ABL Pages: 176
ABL eMH1 WALLBOX Installation Manual preview
eMH1 WALLBOX
Brand: ABL Pages: 94
Jabra TOUR Get Started preview
TOUR
Brand: Jabra Pages: 10
Kuda-Phonebase 055040 Installation Instruction preview
055040
Brand: Kuda-Phonebase Pages: 3
Chevrolet Avalanche 2005 Owner'S Manual preview
Avalanche 2005
Brand: Chevrolet Pages: 494
Toyota RX450h 2010 Emergency Response Manual preview
RX450h 2010
Brand: Toyota Pages: 35
FORM FIT 1303 Installation Instructions preview
1303
Brand: FORM FIT Pages: 2
Honda 08A28-0J6-800 Installation Instructions Manual preview
08A28-0J6-800
Brand: Honda Pages: 32
Honda 08A06-361-210 Installation Instructions preview
08A06-361-210
Brand: Honda Pages: 4
Pro-gard SAFESTOP SS0005 Installation Manual preview
SAFESTOP SS0005
Brand: Pro-gard Pages: 4
Parkeon StradaPAL Installation Manual preview
StradaPAL
Brand: Parkeon Pages: 43
Sears 580.32601 Owner'S Manual preview
580.32601
Brand: Sears Pages: 41
Ford 2001 Explorer Owner'S Manual preview
2001 Explorer
Brand: Ford Pages: 256
VDO RUDDER ANGLE INDICATOR Installation Instructions Manual preview
RUDDER ANGLE INDICATOR
Brand: VDO Pages: 8
Chevrolet 1996 Cavalier Owner'S Manual preview
1996 Cavalier
Brand: Chevrolet Pages: 372
BMW 323Ci Manual preview
323Ci
Brand: BMW Pages: 189
iDataLink ADS-TBSL-GM Install Manual preview
ADS-TBSL-GM
Brand: iDataLink Pages: 6
ULTIMATE SPEED 290923 Operation And Safety Notes preview
290923
Brand: ULTIMATE SPEED Pages: 56

Brands by name

Popular brands

Load more brands